用多通道AD分级采集扩展地震数据采集器的动态范围
|
摘要
地震数据采集是地震信号数字化必不可少的环节,动态范围是其一个重要的性能指标.实际地震信号的动态范围在160dB以上,而目前普遍使用的24位地震数据采集器动态范围相对较小且在50 Hz采样率时最大只达到135dB,致使24位地震数据采集器在实际使用中对小信号分辨率不够,不能有效提取地震信息;在大地震时又容易使数据采集器出现饱和限幅失真的现象而失去地震监测记录功能.本文针对在地震监测和地震研究中需要具有高分辨率和高动态范围的地震数据采集器这个亟待解决的问题,提出一种采用多通道AD转换器并行分级采集的方法,讨论了通道间失配及其标定.对研制实验样机的测试表明,其动态范围在50Hz采样时可以达到157dB以上,线性度优于0.005%.
The seismic data acquisition system is an indispensable process of the digitalization of seismic signals.The quality of this system has a direct effect on the quality of the seismic signal recorded and the final data processing results.There is a wide dynamic range for the observed seismic signal,the total signal amplitude of which could even surpass 160 dB.So it is a dynamic range of broadband seismometers,which is more than 140 dB.However,the widely used 24-bit high-quality seismic data acquisition system in recent times,which is produced based onΔΣAD conventional technology,has a dynamic range of only 135dB@50SPS.As a result,seismic information cannot be extracted effectively in practical earthquake monitoring for both minor and strong signals.The loss of minor signal is due to the fact that data acquisition with low SNR(signal to noise ratio)has no high resolution to identify minor signals,and that the amplitude ofthe signal to record is at the same magnitude order as the resolution of the data acquisition system.The loss of large signal is caused by a saturated clipping distortion that appears in violent earthquakes.This makes local seismograph stations almost lose the ability to record data at the time that firsthand observation resources are needed for earthquake prevention and hazard reduction,and leads to lose precious opportunities to record strong seismic signals for seismic study.Therefore,to meet the application requirements,a multi-channel AD converter sample grading method for extending the dynamic range of seismic data acquisition is put forward in this paper.In the multi-channel AD converter sample grading method,several ADC channels are put in parallel,and simulated input signals are sent to each channel.Synchronous sampling and digital conversion are made on the full range input signal in each channel with different input voltage ranges in each channel for conversion.Meanwhile,the ranges of measurement and the input range of AD converters are matched by modulating waveforms and electrical level displacements in simulated preprocessing circuits in the front ends of each channel.The results are put out in the format of 32-bits converted digital signals after processing and fitted by the CPU-control process unit and multi switch MUX.We adopt the parallel connection of two ADCs in the experimental circuits for a two-level segmented acquisition of input signals.The 24-bit AD chip ADS1255 with fourth-order ΣΔmodulators are used as the chip of the analog-digital converter.The range of AD input signal is extended from ±5Vto±40V(differential)with the resistance attenuating network for the first level of signal,and the resolution of the other level of signal is improved by amplitude limiting and magnification.The ADCs in the two channels collect the input simulated signal synchronously and parallel driven by the same clock.The digital option switch selects channel data according to the magnitude of the signal,and forms a 32-bit output after a data scaling by the control processor.The test results show that the zero input noise voltage has an effective value less than 0.2μV,the noise spectral density is less than 0.05μV/槡Hz,the full-scale input range is±40V,with a dynamic range of 157 dB and linearity better than 0.005% at a sampling rate of 50 Hz.The method of multi-channel AD converter sample grading not only improves the resolution of seismic data acquisition for minor signals,but also enables the acquisition system to record great number of seismic information without saturation in advance to prevent from amplitude limiting.This method can help meet requirements for the large dynamic ranges for data acquisition in seismic monitoring,with low costs and easily to achieve technologically.
The seismic data acquisition system is an indispensable process of the digitalization of seismic signals.The quality of this system has a direct effect on the quality of the seismic signal recorded and the final data processing results.There is a wide dynamic range for the observed seismic signal,the total signal amplitude of which could even surpass 160 dB.So it is a dynamic range of broadband seismometers,which is more than 140 dB.However,the widely used 24-bit high-quality seismic data acquisition system in recent times,which is produced based onΔΣAD conventional technology,has a dynamic range of only 135dB@50SPS.As a result,seismic information cannot be extracted effectively in practical earthquake monitoring for both minor and strong signals.The loss of minor signal is due to the fact that data acquisition with low SNR(signal to noise ratio)has no high resolution to identify minor signals,and that the amplitude ofthe signal to record is at the same magnitude order as the resolution of the data acquisition system.The loss of large signal is caused by a saturated clipping distortion that appears in violent earthquakes.This makes local seismograph stations almost lose the ability to record data at the time that firsthand observation resources are needed for earthquake prevention and hazard reduction,and leads to lose precious opportunities to record strong seismic signals for seismic study.Therefore,to meet the application requirements,a multi-channel AD converter sample grading method for extending the dynamic range of seismic data acquisition is put forward in this paper.In the multi-channel AD converter sample grading method,several ADC channels are put in parallel,and simulated input signals are sent to each channel.Synchronous sampling and digital conversion are made on the full range input signal in each channel with different input voltage ranges in each channel for conversion.Meanwhile,the ranges of measurement and the input range of AD converters are matched by modulating waveforms and electrical level displacements in simulated preprocessing circuits in the front ends of each channel.The results are put out in the format of 32-bits converted digital signals after processing and fitted by the CPU-control process unit and multi switch MUX.We adopt the parallel connection of two ADCs in the experimental circuits for a two-level segmented acquisition of input signals.The 24-bit AD chip ADS1255 with fourth-order ΣΔmodulators are used as the chip of the analog-digital converter.The range of AD input signal is extended from ±5Vto±40V(differential)with the resistance attenuating network for the first level of signal,and the resolution of the other level of signal is improved by amplitude limiting and magnification.The ADCs in the two channels collect the input simulated signal synchronously and parallel driven by the same clock.The digital option switch selects channel data according to the magnitude of the signal,and forms a 32-bit output after a data scaling by the control processor.The test results show that the zero input noise voltage has an effective value less than 0.2μV,the noise spectral density is less than 0.05μV/槡Hz,the full-scale input range is±40V,with a dynamic range of 157 dB and linearity better than 0.005% at a sampling rate of 50 Hz.The method of multi-channel AD converter sample grading not only improves the resolution of seismic data acquisition for minor signals,but also enables the acquisition system to record great number of seismic information without saturation in advance to prevent from amplitude limiting.This method can help meet requirements for the large dynamic ranges for data acquisition in seismic monitoring,with low costs and easily to achieve technologically.
引文
Black W C,Hodges D A.1980.Time interleaved converter arrays.IEEE J.Solid-State Circuits,15(6):1022-1029.
Bogner P,Kuttner F,Kropf C,et al.2006.A 14b 100MS/s digitally self-calibrated pipelined ADC in 0.13μm CMOS.∥IEEE International Solid-State Circuits Conference,Digest of Technical Papers.San Francisco,CA:IEEE,832-841.
Candy J C,Temes G C.1987.Oversampling methods for A/D and D/A conversion.∥IEEE Transactions on Circuits and Systems.IEEE.
Chen Z B,Teng J W,Lin J,et al.2006.Design of BSR-2broad band seismic recorder.Chinese J.Geophys.(in Chinese),49(5):1475-1481.
Elbornsson J,Gustafsson F,Eklund J E.2003.Analysis of mismatch noise in randomly interleaved ADC system.∥Proceedings of the2003IEEE International Conference on Acoustics,Speech,and Signal Processing.Hong Kong,China:IEEE.
El-Chammas M,Murmann B.2009.General analysis on the impact of phase-skew in time-interleaved ADCs.IEEE Trans.Circuits Syst.I,Reg.Papers,56(5):902-910.
Evans J R,Followill F,Hutt C R,et al.2010.Method for calculating self-noise spectra and operating ranges for seismographic inertial sensors and recorders.Seismological Research Letters,81(4):640-646.
Gao S H,Xue B,Jiang J M,et al.2012.Idea of high performance seismic data acquisition system.Recent Developments in World Seismology(in Chinese),(6):173.
Ge H K,Chen H C,Ouyang B,et al.2013.Transportable seismometer response to seismic noise in vault.Chinese J.Geophys.(in Chinese),56(3):857-868,doi:10.6038/cjg20130315.
Geerts Y,Steyaert M S J,Sansen W.2000.A high-performance multibitΔΣCMOS ADC.IEEE Journal of Solid-State Circuits,35(12):1829-1840.
Harrison R R,Charles C.2003.A low-power low-noise CMOS for amplifier neural recording applications.IEEE J.Solid-State Circuits,38(6):958-965.
Huang S,Levy B C.2006.Adaptive blind calibration of timing offset and gain mismatch for two-channel time-interleaved ADCs.IEEE Trans.on Circuits Syst.I:Reg.Papers,53(6):1278-1288.
Johansson H,Lowenborg P.2002.Reconstruction of nonuniformly sampled bandlimited signals by means of digital fractional delay filters.IEEE Trans.Signal Process.,50(11):2757-2767.
Kurosawa N,Kobayashi H,Maruyama K,et al.2001.Explicit analysis of channel mismatch effects in time-interleaved ADCsystems.IEEE Trans.Circuits Syst.I:Fundam.Theory Appl.,48(3):261-271.
Lee K,Temes G C.2006.Enhanced split-architecture delta-sigma ADC.∥Proceedings of the 13th IEEE International Conference on Electronics,Circuits and Systems.Nice:IEEE,427-430.
Lee Z M,Wang C Y,Wu J T.2007.A CMOS 15-bit 125-MS/s time-interleaved ADC with digital background calibration.IEEE Journal of Solid-State Circuits,42(10):2149-2160.
Leger G,Peralias E,Rueda A,et al.2004.Impact of random channel mismatch on the SNR and SFDR of time-interleaved ADCs.IEEE Trans.Circuits Syst.I:Fundam.Theory Appl.,51(1):140-150.
Li G.2005.Study and implementation of improving ADC resolution based on over sampling technology.Computer Engineering(in Chinese),31(S1):244-248.
Li J,Xue B,Zhu X Y,et al.2013a.Key technology research of seismic data acquisition system.Seismological and Geomagnetic Observation and Research(in Chinese),34(3-4):179-185,doi:10.3969/j.issn.1003-3246.2013.03/04.033.
Li J,Liu Y,Liu H,et al.2013b.A timing skew calibration scheme in time-interleaved ADC.Journal of Computer and Communications,1(6):37-40.
Li W,Chen Z B.2006.Noise analysis in data acquisition channel of broad band seismic recorder.Journal of Jilin University(Information Science Edition)(in Chinese),24(5):462-465.
Liao S G.2005.The limitation of 24-bits seismic data acquisition system for high precision petroleum seismic exploration.Science and Technology(in Chinese),15(2):13-15.
Liu H C,Lee Z M,Wu J T.2005.A 15-b 40-MS/s CMOSpipelined analog-to-digital converter with digital background calibration.IEEE J.Solid-State Circuits,40(5):1047-1056.
Luo Y X,Wu X Y,Zeng J,et al.2006.Design of a 7-bands instantaneous floating point gain amplifier.Journal of EEE(in Chinese),28(6):39-41,49.
Marelli D,Mahata K,Fu M Y.2009.Linear LMS compensation for timing mismatch in time-interleaved ADCs.IEEE Transaction on Circuits and Systems I:Regular Papers,56(11):2476-2486.
Marques A,Peluso V,Steyaert M S,et al.1998.Optimal parameters forΔΣmodulator topologies.IEEE Trans.Circuits Syst.II,45(9):1232-1241.
McNeill J,Coln M C W,Larivee B J.2005.‘Split-ADC’architecture for deterministic digital background calibration of a 16-bit 1-MS/s ADC.IEEE J.Solid-State Circuits,40(12):2437-2445.
Medeiro F,Pérez-VerdúB,Rodríquez-Vázquez A.1999.Top-Down Design of High-Performance Sigma-Delta Modulators.US:Springer.
Melton B S.1976.The sensitivity and dynamic range of inertial seismographs.Rev.Geophys.,14(1):93-116.
Mosheni P,Najafi K.2004.A fully integrated neural recording amplifier with DC input stabilization.IEEE Trans.Biomed.Eng.,51(5):832-837.
Mukhanov O A,Semenov V K,Li W Q,et al.2001.A superconductor high-resolution ADC.IEEE Transactions on Applied Superconductivity,11(1):601-606.
Mukhanov O A,Brock D K,Kirichenko A F,et al.1999.Progress in the development of a superconductive high-resolution ADC.∥Extended Abstracts of 7th ISEC′99.Berkeley,CA,13-16.
Muramatu I.1995.Development of a broadband velocity type strong motion seismometer and its recording range.Journal of the Seismological Society of Japan,48(2):247-256.
Norsworthy S R,Schreier R,Temes G C.1996.Delta-Sigma Data Converters:Theory,Design,and Simulation.NY:IEEE Press.
Petraglia A,Mitra S K.1991.Analysis of mismatch effects among A/D converters in a time-interleaved waveform digitizer.IEEE Trans.Instrum.Meas.,40(5):831-835.
Mendel S,Vogel C.2006.A compensation method for magnitude response mismatches in two-channel time-interleaved analogto-digital converters.∥Electronics,Circuits and Systems,2006.ICECS′06.13th IEEE International Conference on.712-715.
Rao L P,Sitthimahachaikul N,Hurst P J.2012.Correcting the effects of mismatches in time-interleaved analog adaptive FIRequalizers.IEEE Transactions on Circuits and System I:Regular Papers,59(11):2529-2542.
Razavi B.1995.Principles of Data Conversion System Design.New York:IEEE Press.
Ringler A T,Hutt C R,Evans J R,et al.2011.A comparison of seismic instrument noise coherence analysis techniques.Bulletino f the Seismological society of America,101(2):558-567.
Romeo G,Spinelli G.2013.Extending a Lippmann style seismometer′s dynamic range by using a non-linear feedback circuit.Adv.Geosci.,36:27-30,doi:10.5194/adgeo-36-27-2013.
Rylov S V,Robertazzi R P.1995.Superconducting high-resolution A/D converter based on phase modulation and multichannel timing arbitration.IEEE Trans.Appl.Supercond.,5(2):2260-2263.
Rylov S V,Brock D K,Gaidarenko D V,et al.1999.High resolution ADC using phase modulation-demodulation architecture.IEEETrans.Appl.Supercond.,9(2):3016-3019.
Saleem S,Vogel C.2010.Adaptive compensation of frequency response mismatches in high-resolution time-interleaved ADCs using a low-resolution ADC and a time-varying filter.∥Proceedings of 2010IEEE International Symposium on Circuits and Systems.Paris:IEEE,561-564.
Saleem S,Vogel C.2011.Adaptive blind background calibration of polynomial-represented frequency response mismatches in a two-channel time-interleaved ADC.IEEE Transactions on Circuits and Systems-I:Regular Papers,58(6):1300-1310.
Satarzadeh P,Levy B C,Hurst P J.2007.Bandwidth mismatch correction for a two-channel time-interleaved A/D converter.∥Proceedings of the IEEE International Symposium on Circuits and Systems.New Orleans,LA:IEEE,1705-1708.
Seo M,Rodwell M J W,Madhow U.2005.Blind correction of gain and timing mismatches for a two-channel time-interleaved analog-to-digital converter.∥Conference Record of the 39th Asilomar Conference on Signals,Systems and Computers.Pacific Grove,CA:IEEE,1121-1125.
Siragusa E,Galton I.2004.A digitally enhanced 1.8-V 15-bit 40-MSample/s CMOS pipelined ADC.IEEE J.Solid-State Circuits,39(12):2126-2138.
Sun X,Luo G E.2008.Design and implementation of a high precision seismic data acquisition system.Computer Measurement&Control(in Chinese),16(6):881-883.
Tsai T H,Hurst P J,Lewis S H.2006.Bandwidth mismatch and its correction in time-interleaved analog-to-digital converters.IEEE Trans.Circuits Syst.II:Exp.Briefs,53(10):1133-1137.
Vogel C.2005.The impact of combined channel mismatch effects in time-interleaved ADCs.IEEE Trans.Instrum.Meas.,54(1):415-427.
Vogel C,Saleem S,Mendel S.2008.Adaptive blind compensation of gain and timing mismatches in m-channel time-interleaved ADCs.∥Proceedings of the 15th IEEE International Conference on Electronics,Circuits and Systems.St.Julien′s:IEEE,49-52.
Wang P,Li X J.2002.Improving ADC resolution and signal-noise ratio by oversampling.Chinese Journal of Scientific Instrument(in Chinese),23(3S):1-2.
Wang C F,Yang X Y,Song C,et al.2010.The Principal shock waves of the 2008Wenchuan 8.0Earthquake Recorded by two types of Acquisition device.Earthquake Research in Sichuan(in Chinese),(3):19-22.
Xu Q,Duan Z M.2014.A signal reconstruction method for timeinterleaved ADC converters.Journal of Information&Computational Science,11(1):123-132.
Yin M,Ghovanloo M.2007.A low-noise preamplifier with adjustable gain and bandwidth for biopotential recording applications.∥IEEE International Symposium on Circuits and Systems.New Orleans,LA:IEEE,321-324.
Yuan Z L,Cao G H.2000.Improvement on seismograph data collection system.Journal of Daqing Petroleum Institute(in Chinese),24(4):15-17.
陈祖斌,滕吉文,林君等.2006.BSR-2宽频带地震记录仪的研制.地球物理学报,49(5):1475-1481.
高尚华,薛兵,蒋久明等.2012.高性能地震数据采集方案构想.国际地震动态,(6):173.
葛洪魁,陈海潮,欧阳飚等.2013.流动地震观测背景噪声的台基响应.地球物理学报,56(3):857-868,doi:10.6038/cjg20130315.
李国.2005.基于过采样技术提高ADC分辨率的研究与实现.计算机工程,31(增刊):244-248.
李江,薛兵,朱小毅等.2013.地震数据采集器关键技术研究.地震地磁观测与研究,34(3-4):179-185,doi:10.3969/j.issn.1003-3246.2013.03/04.033.
李威,陈祖斌.2006.宽频地震仪数据采集通道的噪声分析.吉林大学学报(信息科学版),24(5):462-465.
廖声刚.2005.24位地震数据采集系统进行高精度石油地震勘探的局限性.江汉石油科技,15(2):13-15.
罗运先,吴雄英,曾敬等.2006.七阶型瞬时浮点增益放大器设计探讨.电气电子教学学报,28(6):39-41,49.
孙娴,罗桂娥.2008.一种高精度地震勘探数据采集系统的设计与实现.计算机测量与控制,16(6):881-883.
王萍,李小京.2002.利用过采样法提高A/D分辨率和信噪比.仪器仪表学报,23(3增刊):1-2.
王翠芳,杨晓源,宋澄等.2010.两种采集器记录的汶川8.0级主震波形.四川地震,(3):19-22.
袁子龙,曹广华.2000.地震仪数据采集系统的改进.大庆石油学院学报,24(4):15-17.
Bogner P,Kuttner F,Kropf C,et al.2006.A 14b 100MS/s digitally self-calibrated pipelined ADC in 0.13μm CMOS.∥IEEE International Solid-State Circuits Conference,Digest of Technical Papers.San Francisco,CA:IEEE,832-841.
Candy J C,Temes G C.1987.Oversampling methods for A/D and D/A conversion.∥IEEE Transactions on Circuits and Systems.IEEE.
Chen Z B,Teng J W,Lin J,et al.2006.Design of BSR-2broad band seismic recorder.Chinese J.Geophys.(in Chinese),49(5):1475-1481.
Elbornsson J,Gustafsson F,Eklund J E.2003.Analysis of mismatch noise in randomly interleaved ADC system.∥Proceedings of the2003IEEE International Conference on Acoustics,Speech,and Signal Processing.Hong Kong,China:IEEE.
El-Chammas M,Murmann B.2009.General analysis on the impact of phase-skew in time-interleaved ADCs.IEEE Trans.Circuits Syst.I,Reg.Papers,56(5):902-910.
Evans J R,Followill F,Hutt C R,et al.2010.Method for calculating self-noise spectra and operating ranges for seismographic inertial sensors and recorders.Seismological Research Letters,81(4):640-646.
Gao S H,Xue B,Jiang J M,et al.2012.Idea of high performance seismic data acquisition system.Recent Developments in World Seismology(in Chinese),(6):173.
Ge H K,Chen H C,Ouyang B,et al.2013.Transportable seismometer response to seismic noise in vault.Chinese J.Geophys.(in Chinese),56(3):857-868,doi:10.6038/cjg20130315.
Geerts Y,Steyaert M S J,Sansen W.2000.A high-performance multibitΔΣCMOS ADC.IEEE Journal of Solid-State Circuits,35(12):1829-1840.
Harrison R R,Charles C.2003.A low-power low-noise CMOS for amplifier neural recording applications.IEEE J.Solid-State Circuits,38(6):958-965.
Huang S,Levy B C.2006.Adaptive blind calibration of timing offset and gain mismatch for two-channel time-interleaved ADCs.IEEE Trans.on Circuits Syst.I:Reg.Papers,53(6):1278-1288.
Johansson H,Lowenborg P.2002.Reconstruction of nonuniformly sampled bandlimited signals by means of digital fractional delay filters.IEEE Trans.Signal Process.,50(11):2757-2767.
Kurosawa N,Kobayashi H,Maruyama K,et al.2001.Explicit analysis of channel mismatch effects in time-interleaved ADCsystems.IEEE Trans.Circuits Syst.I:Fundam.Theory Appl.,48(3):261-271.
Lee K,Temes G C.2006.Enhanced split-architecture delta-sigma ADC.∥Proceedings of the 13th IEEE International Conference on Electronics,Circuits and Systems.Nice:IEEE,427-430.
Lee Z M,Wang C Y,Wu J T.2007.A CMOS 15-bit 125-MS/s time-interleaved ADC with digital background calibration.IEEE Journal of Solid-State Circuits,42(10):2149-2160.
Leger G,Peralias E,Rueda A,et al.2004.Impact of random channel mismatch on the SNR and SFDR of time-interleaved ADCs.IEEE Trans.Circuits Syst.I:Fundam.Theory Appl.,51(1):140-150.
Li G.2005.Study and implementation of improving ADC resolution based on over sampling technology.Computer Engineering(in Chinese),31(S1):244-248.
Li J,Xue B,Zhu X Y,et al.2013a.Key technology research of seismic data acquisition system.Seismological and Geomagnetic Observation and Research(in Chinese),34(3-4):179-185,doi:10.3969/j.issn.1003-3246.2013.03/04.033.
Li J,Liu Y,Liu H,et al.2013b.A timing skew calibration scheme in time-interleaved ADC.Journal of Computer and Communications,1(6):37-40.
Li W,Chen Z B.2006.Noise analysis in data acquisition channel of broad band seismic recorder.Journal of Jilin University(Information Science Edition)(in Chinese),24(5):462-465.
Liao S G.2005.The limitation of 24-bits seismic data acquisition system for high precision petroleum seismic exploration.Science and Technology(in Chinese),15(2):13-15.
Liu H C,Lee Z M,Wu J T.2005.A 15-b 40-MS/s CMOSpipelined analog-to-digital converter with digital background calibration.IEEE J.Solid-State Circuits,40(5):1047-1056.
Luo Y X,Wu X Y,Zeng J,et al.2006.Design of a 7-bands instantaneous floating point gain amplifier.Journal of EEE(in Chinese),28(6):39-41,49.
Marelli D,Mahata K,Fu M Y.2009.Linear LMS compensation for timing mismatch in time-interleaved ADCs.IEEE Transaction on Circuits and Systems I:Regular Papers,56(11):2476-2486.
Marques A,Peluso V,Steyaert M S,et al.1998.Optimal parameters forΔΣmodulator topologies.IEEE Trans.Circuits Syst.II,45(9):1232-1241.
McNeill J,Coln M C W,Larivee B J.2005.‘Split-ADC’architecture for deterministic digital background calibration of a 16-bit 1-MS/s ADC.IEEE J.Solid-State Circuits,40(12):2437-2445.
Medeiro F,Pérez-VerdúB,Rodríquez-Vázquez A.1999.Top-Down Design of High-Performance Sigma-Delta Modulators.US:Springer.
Melton B S.1976.The sensitivity and dynamic range of inertial seismographs.Rev.Geophys.,14(1):93-116.
Mosheni P,Najafi K.2004.A fully integrated neural recording amplifier with DC input stabilization.IEEE Trans.Biomed.Eng.,51(5):832-837.
Mukhanov O A,Semenov V K,Li W Q,et al.2001.A superconductor high-resolution ADC.IEEE Transactions on Applied Superconductivity,11(1):601-606.
Mukhanov O A,Brock D K,Kirichenko A F,et al.1999.Progress in the development of a superconductive high-resolution ADC.∥Extended Abstracts of 7th ISEC′99.Berkeley,CA,13-16.
Muramatu I.1995.Development of a broadband velocity type strong motion seismometer and its recording range.Journal of the Seismological Society of Japan,48(2):247-256.
Norsworthy S R,Schreier R,Temes G C.1996.Delta-Sigma Data Converters:Theory,Design,and Simulation.NY:IEEE Press.
Petraglia A,Mitra S K.1991.Analysis of mismatch effects among A/D converters in a time-interleaved waveform digitizer.IEEE Trans.Instrum.Meas.,40(5):831-835.
Mendel S,Vogel C.2006.A compensation method for magnitude response mismatches in two-channel time-interleaved analogto-digital converters.∥Electronics,Circuits and Systems,2006.ICECS′06.13th IEEE International Conference on.712-715.
Rao L P,Sitthimahachaikul N,Hurst P J.2012.Correcting the effects of mismatches in time-interleaved analog adaptive FIRequalizers.IEEE Transactions on Circuits and System I:Regular Papers,59(11):2529-2542.
Razavi B.1995.Principles of Data Conversion System Design.New York:IEEE Press.
Ringler A T,Hutt C R,Evans J R,et al.2011.A comparison of seismic instrument noise coherence analysis techniques.Bulletino f the Seismological society of America,101(2):558-567.
Romeo G,Spinelli G.2013.Extending a Lippmann style seismometer′s dynamic range by using a non-linear feedback circuit.Adv.Geosci.,36:27-30,doi:10.5194/adgeo-36-27-2013.
Rylov S V,Robertazzi R P.1995.Superconducting high-resolution A/D converter based on phase modulation and multichannel timing arbitration.IEEE Trans.Appl.Supercond.,5(2):2260-2263.
Rylov S V,Brock D K,Gaidarenko D V,et al.1999.High resolution ADC using phase modulation-demodulation architecture.IEEETrans.Appl.Supercond.,9(2):3016-3019.
Saleem S,Vogel C.2010.Adaptive compensation of frequency response mismatches in high-resolution time-interleaved ADCs using a low-resolution ADC and a time-varying filter.∥Proceedings of 2010IEEE International Symposium on Circuits and Systems.Paris:IEEE,561-564.
Saleem S,Vogel C.2011.Adaptive blind background calibration of polynomial-represented frequency response mismatches in a two-channel time-interleaved ADC.IEEE Transactions on Circuits and Systems-I:Regular Papers,58(6):1300-1310.
Satarzadeh P,Levy B C,Hurst P J.2007.Bandwidth mismatch correction for a two-channel time-interleaved A/D converter.∥Proceedings of the IEEE International Symposium on Circuits and Systems.New Orleans,LA:IEEE,1705-1708.
Seo M,Rodwell M J W,Madhow U.2005.Blind correction of gain and timing mismatches for a two-channel time-interleaved analog-to-digital converter.∥Conference Record of the 39th Asilomar Conference on Signals,Systems and Computers.Pacific Grove,CA:IEEE,1121-1125.
Siragusa E,Galton I.2004.A digitally enhanced 1.8-V 15-bit 40-MSample/s CMOS pipelined ADC.IEEE J.Solid-State Circuits,39(12):2126-2138.
Sun X,Luo G E.2008.Design and implementation of a high precision seismic data acquisition system.Computer Measurement&Control(in Chinese),16(6):881-883.
Tsai T H,Hurst P J,Lewis S H.2006.Bandwidth mismatch and its correction in time-interleaved analog-to-digital converters.IEEE Trans.Circuits Syst.II:Exp.Briefs,53(10):1133-1137.
Vogel C.2005.The impact of combined channel mismatch effects in time-interleaved ADCs.IEEE Trans.Instrum.Meas.,54(1):415-427.
Vogel C,Saleem S,Mendel S.2008.Adaptive blind compensation of gain and timing mismatches in m-channel time-interleaved ADCs.∥Proceedings of the 15th IEEE International Conference on Electronics,Circuits and Systems.St.Julien′s:IEEE,49-52.
Wang P,Li X J.2002.Improving ADC resolution and signal-noise ratio by oversampling.Chinese Journal of Scientific Instrument(in Chinese),23(3S):1-2.
Wang C F,Yang X Y,Song C,et al.2010.The Principal shock waves of the 2008Wenchuan 8.0Earthquake Recorded by two types of Acquisition device.Earthquake Research in Sichuan(in Chinese),(3):19-22.
Xu Q,Duan Z M.2014.A signal reconstruction method for timeinterleaved ADC converters.Journal of Information&Computational Science,11(1):123-132.
Yin M,Ghovanloo M.2007.A low-noise preamplifier with adjustable gain and bandwidth for biopotential recording applications.∥IEEE International Symposium on Circuits and Systems.New Orleans,LA:IEEE,321-324.
Yuan Z L,Cao G H.2000.Improvement on seismograph data collection system.Journal of Daqing Petroleum Institute(in Chinese),24(4):15-17.
陈祖斌,滕吉文,林君等.2006.BSR-2宽频带地震记录仪的研制.地球物理学报,49(5):1475-1481.
高尚华,薛兵,蒋久明等.2012.高性能地震数据采集方案构想.国际地震动态,(6):173.
葛洪魁,陈海潮,欧阳飚等.2013.流动地震观测背景噪声的台基响应.地球物理学报,56(3):857-868,doi:10.6038/cjg20130315.
李国.2005.基于过采样技术提高ADC分辨率的研究与实现.计算机工程,31(增刊):244-248.
李江,薛兵,朱小毅等.2013.地震数据采集器关键技术研究.地震地磁观测与研究,34(3-4):179-185,doi:10.3969/j.issn.1003-3246.2013.03/04.033.
李威,陈祖斌.2006.宽频地震仪数据采集通道的噪声分析.吉林大学学报(信息科学版),24(5):462-465.
廖声刚.2005.24位地震数据采集系统进行高精度石油地震勘探的局限性.江汉石油科技,15(2):13-15.
罗运先,吴雄英,曾敬等.2006.七阶型瞬时浮点增益放大器设计探讨.电气电子教学学报,28(6):39-41,49.
孙娴,罗桂娥.2008.一种高精度地震勘探数据采集系统的设计与实现.计算机测量与控制,16(6):881-883.
王萍,李小京.2002.利用过采样法提高A/D分辨率和信噪比.仪器仪表学报,23(3增刊):1-2.
王翠芳,杨晓源,宋澄等.2010.两种采集器记录的汶川8.0级主震波形.四川地震,(3):19-22.
袁子龙,曹广华.2000.地震仪数据采集系统的改进.大庆石油学院学报,24(4):15-17.