隔震结构体系的地震反应和抗震可靠度研究
详细信息    本馆镜像全文|  推荐本文 |  |   获取CNKI官网全文
摘要
基础隔震是一种目前在建筑结构减震方面很好的方法,它通过软弱隔震层的大变形来减少地震地面运动对上部结构的影响,减少建筑结构地震反应加速度和层间剪力,从根本上减少地震对人身安全、建筑物及其室内重要设备的破坏。
     本论文在广泛调研国内外隔震结构研究成果的基础上,从基础隔震结构的动力时程分析出发,采用随机有限元法,计算隔震结构在某一地震波作用下位移、速度、加速度反应的均值、方差。假设其反应的分布,计算出结构的承载力时程可靠度。并与传统的非隔震结构抗震可靠度相比较。说明隔震结构在防止结构层间位移过大而引起破坏有很好的效果。根据隔震结构的特点,本文在考虑了边缘隔震支座不产生拉应力及支座压应力不超过其承载压应力这两个条件下,建立隔震结构的抗倾覆极限状态方程,最后得出隔震结构抗倾覆可靠度的计算公式。
     在考虑了结构使用期限内各个等级地震发生概率的基础上,运用时程可靠度分析,计算了隔震结构使用期限内的承载力可靠度和抗倾覆可靠度,并与传统的非隔震结构的分析结果相比较。
     本文最后就影响隔震结构可靠度的一些有关参数进行初步分析。这些参数主要是:刚度K、阻尼C和质量M的变异系数;结构的高宽比;隔震层的阻尼比;上部结构与隔震层的刚度比等。本文还探讨了影响高宽比限值的一些因素。
     本文通过隔震结构可靠度的计算,得出的主要结论如下:
     ①隔震结构在多遇地震的作用下,隔震层的承载力可靠度大于上部结构的承载力可靠度,但在罕遇地震作用下,隔震层的承载力可靠度有可能会小于上部结构的承载力可靠度。
     ②隔震结构使用期限内保持“中震可修”和“大震不倒”的概率大于非隔震结构;隔震结构在使用期限内有很高的承载力可靠度和抗倾覆可靠度。
     ③隔震结构的抗倾覆可靠度主要受高宽比限制,高宽比的限值又与场地条件,地震加速度峰值及隔震层的刚度(结构周期)有关。
     ④上部结构与隔震层的刚度比是隔震结构的一个很重要的参数,它是决定结构周期的主要因素,对结构的抗倾覆可靠度和承载力可靠度都有重要影响。
     ⑤隔震层的阻尼对结构的抗倾覆可靠度及承载力可靠都有影响,但对抗倾覆可靠度的影响更为显著。
Base isolation is an effective design technique against the earthquake damage to the structure. The lateral flexibility of the base isolation system increases the fundamental period of the structure and thus minimize the lateral load transferred to the superstructure during the strong earthquake.
    On the basis of the wide investigation of the achievement home and abroad about the base isolation, this dissertation completed the mean and variance of the displacement, velocity and acceleration induced by given earthquake base on the time-history response and stochastic FEM. Then we can figure out the Time-history reliability of bearing capacity on the assumption that distribution of structure response of earthquake referring to relation literature. The base isolation structure is safer than the ordinary structure when we compare their reliability.
    For the overturn problem of the base isolation structure, the limit state equation and anti-overture reliability formula of base isolation structure was deduced in the dissertation and applied to the example analysis
    Some parameter that influences reliability of structure was analyzed preliminarily in this dissertation. They include variance of the structural stiffness (K), damping (C) and mass (M), the ratio of height to width of the structure, damping ratio of the isolated layer, stiffness ratio of superstructure to isolated layer. The main conclusion is: the effect of variance of K, C and M towards structural reliability is small, the effect of the ration of height to width is significant towards structural anti-overturn reliability, the isolation layers' damping ratio and stiffness ratio influence the reliability of both bearing capability and anti-overturn and the latter is more significant. Some factor that influence the limit of height-to-width ratio is discussed because reliability of base isolation structure is mainly determined by height-to- width ratio.
引文
[1].崔鸿超,日本兵库县南部地震震害综述,建筑结构学报,Vol.17,No.2,1996。
    [2].张敏政,土耳其伊兹米特地震震害考察,工程抗震,No.4,2000.12。
    [3].许清风,蒋永生,傅传国,梁书亭,关于土耳其和台湾大地震的一点思考,工程抗震,No.3,2000.9。
    [4].王亚勇,皮声援,台湾大地震及震害经验。工程抗震,No.2,2000.6。
    [5].蔡丹绎,南京电视塔风振控制工程的试验研究,博士学位论文(东南大学),1998.1。
    [6].张顺宝,人工神经网络用于结构主动控制理论与应用研究,博士学位论文(东南大学),1999.1。
    [7].李清原编译,智能建筑用的关动耗能器,工程抗震,No.4,1995.12。
    [8].日本免震构造协会编,叶列平译,图解隔震结构入门,科学出版社,1998。
    [9].武田寿一主编,纪晓惠、陈良、鄢宁译,王松涛校,建筑物隔震防振与控振。中国建筑工业出版社,1997.4。
    [10].法隆寺国宝保存委员会,法隆寺国宝保存工事报告书,第13期,昭和30年。
    [11]. Calantaricnts,J.A.: Improvements in and Connected with Building and Other Works and Appurtenances to Resist the Action of Earthquake and the Like.Paper No.325371 ,Engineering Library, Stanford University, California, 1909。
    [12].唐家华,刘再华,建筑结构基础隔震,华中理工大学出版社,1993.8
    [13].黄水林,孔建国,章熙海,张雪亮,隔震技术的发展及其对未来建筑设计思想的影响,工程抗震,No.1,2000.3。
    [14]. Nawawi Chouw. Reduction of Structural Vibrations due to Impediment of Soil Excitations. Proceedings of the second World Conference on Structural Control. 1998: Kyoto,Japan, p.1053-1062。
    [15]. R.J. Skinner, W.H. Robinson, G. H. MeVerry著:谢礼立,周雍年,赵兴权译校,工程隔震概论,地震出版社,1996。
    [16].中华人民共和国交通运输(公路)行业标准JT3132.3-90.公路桥梁扳式橡胶支座成品力学性能检验规则,1990.6。
    [17].中华人民共和国交通行业标准JT/T44-93.公路桥梁板式橡胶支座,1993.8。
    [18].中华人民共和国交通行业标准JT391-1999.公路桥梁盆式像胶支座,1999.4。
    [19].常熟橡胶厂企业标准,球冠圆型板式橡胶支座,2000.5。
    [20].周云,隔震结构设计、应用与发展,华南建设学报,1998,10。
    [21].徐忠根,周福霖,丘湘泉,汕头博物馆结构动力分析,世界地震工程,No.2,1996.5。
    [22].徐忠根,周福霖,多层钢结构基础隔震性能研究,地震工程与工程震动,Vol.3,1999。
    [23].黄襄云,王清敏,韦定国,姚谦峰,动复位基础隔震体系的试验研究,工程抗震,Vol.3,No.3.2000.9。
    [24]. Jangid, R.S. Stochastic seismic response or structures isolated by rolling rods. Engineering Structures. Vol.22.Junc,2000, p.937-946。
    [25].周锡元,韩淼,李大望,曾德民,并联和串联基础隔震体系地震反应的某些特征,工程抗震,1995.12。
    [26].杨树标,砌体并联复合隔震体系的隔震性能研究,工业建筑,Vol.12,2000。
    
    
    [27].施卫星,王群,层间隔震原理和设计方法,工程抗震,1997.12。
    [28].秦新刚.建筑物层间隔震的理论、试验和应用研究,博士学位论文,东南大学,1998。
    [29]. James M. Kelly. The Current State of Base Isolation in the United States. Proceedings of the second World Conference on Structural Control, 1998: Kyoto,Japan, p. 1043-1052。
    [30]. Vulcano, Alfonso. Comparative study of tire earthquake and wind dynamic responses of base-isolated buildings. Journal of Wing Engineering and Industrial Aerodynamics. Vol.74-76, April 1, 1998, p.751-764。
    [31]. Moroni, Maria O.; Sarrazin, Mauricio; Boroschek, Ruben. Experiments on a base-isolated building in Santiago, Chile. Engineering Structures, Vol.20, August, 1998, p.720-725。
    [32]. Chen Yu, Ahmadi Goodarz. Performance of a high damping rubber bearing base isolation system for a shear beam structure. Earthquake Engineering & Structural Dynamics, Vol.23, No.7,July, 1994, p.729-744。
    [33]. Ilwang, J.S.; Hsu.T.Y A fractional derivative model to include effect of ambient temperature on HDR bearings. Engineering Structures,Vol.23,May,2001 .p.484-490。
    [34].杜永峰,许铁生.多层隔震框架多自由度体系的解耦动力分析,甘肃工业大学学报,Vol.22,No.1,1996
    [35].杜永峰,狄生奎,尹维祥,韩建平,隔震结构等代体系动力响应的小参数逼近解法,甘肃工业大学学报,Vol.2,2000。
    [36].施卫星,李正升,汪大绥,基础隔震位移反应谱及其应用,同济大学学报(自然科学版),Vol.2,2000。
    [37].杨佑发,周福霖,隔震结构地震反应分析的实用计算方法,世界地震工程,Vol.1,2000。
    [38].杜永峰,赵国藩,隔震结构中非经典阻尼影响及最佳阻尼比分析,地震工程与工程震动Vol.3,2000。
    [39].周云,徐彤,贺明玄,基础隔震结构的能量设计方法地震工程与工程震动Vol.3,2000。
    [40].张提波,唐家祥,主动基础隔震结构随机最优控制,噪哪声与振动控制Vol.2,1999
    [41]. 1-Kwang Chang, Christopher J.Podstawski and Kathryn Schuth. A New Concept on Live Load Balance Strategy For Smart 3-D Seismic Base Isolation Design for High-tech Industrial Buildings. Proceedings of the second World Conference on Structural Control, 1998:Kyoto,Japan.p.1668-1675
    [42].周云,结构减震控制技术的研究、应用与发展,华南建设学院西院,1998.4。
    [43].张耀庭,刘再华,小型叠层橡胶支座水平刚度的实验研究,世界地震工程Vol.2,1999。
    [44].周锡元,韩淼,曾德民,樊水荣,具有软着陆保护的橡胶支座隔震体系,建筑结构学报Vol.5,2000
    [45].韩淼,周锡元,基础隔震建筑软碰撞保护分析,建筑科学,Vol.1,1999
    [46].马玉春,基础隔震模式和敏感度分析,工程抗震,1999.2。
    [47].江宜成,唐家祥,李媛萍,基础隔震结构扭转振动反应分析,噪声与振动控制,Vol.1,2000。
    [48]. Pan,T.C. and Kelly, J.M. Seismic Response of Tensional Coupled Base Isolated Building, Earthquake Engineering and Structural Dynamics, Vol. 11,p. 113-128.
    [49]. Ycong-bin Y. and Wei-his H. Seismic Response of Light Equipment in Torsional Buildings, Earthquake Engineering and Structural Dynandcs,Vol.22,p. 113-128
    [50]. Nagarajaiah Satish, Reinhorn Andrei M., Constantinou Michalakis C. Torsion in base-isolated structures with clastomcric isolation systems. Journal of Structural Engineering,
    
    Vol.19. No. 10, October, 1993, p.2932-2951。
    [51].许斌,唐家祥,基础隔震叠层橡胶支座耐久性试验研究,工程隔震,1995.12
    [52].刘义光,周福霖,庄学真,冯德民,三山刚史,加藤泰正,铅芯夹层橡胶隔震垫基本力学性能研究,地震工程与工程振动,Vol.1,1999。
    [53]. Freudenthal, A.M., Safety and Probability of Structural failure, Proc., ASCE, V.80, No. 408, 563, 1954; V.81, No. 664, 765, 1955
    [54].赵国藩,曹居易,张宽权,工程结构可靠度,水利电力出版社,1984.12。
    [55]. Lind, N.C., Consistent Partial Safety Factors, ASCE, V.97, No.ST6, June, 1971。
    [56].葛燕,混凝土结构弹塑性时程可靠度分析,硕士学位论文(四川大学),2002
    [57].李典庆,周建方,结构可靠度计算方法评述,河海大学常州分校学报,2000,3.34~42。
    [58].赵国藩,结构可靠度的实用分析方法,建筑结构学报,1984,5(3):1-10。
    [59].栾淑梅,结构可靠度的简捷分析方法,建筑结构学报,1988,12:57~63。
    [60].郑铎,吴世伟,线性化极限状态方程及归一型算法,南京:全国第二届工程结构可靠性学术交流会议论文集,1992:45~51。
    [61].贡金鑫,结构可靠指标的一种新的迭代方法,计算结构力学及其庆用,1995,12(3):369~373。
    [62].李继华,结构可靠性分析的优化算法,建筑结构学报,1987,8(2):23~30
    [63]. C.G. Bucher. A Fast and Efficient Response Surface Approach for Structural Reliability Problems. Structural Safety, 1990,7(1); 57~66。
    [64]. Yan-Gang Zhao, Tetsuro Ono. (New Approximations for SORM. Journal of Engineering Mechanics. 1999,125(1):79~93。
    [65].赵雷等,结构地震可靠度理论研究进展,建筑结构,2000,12.60~64。
    [66]. Shan, H. C. Dong, N. M. Reliability Assessment of Existing Buildings subjected to probabilistic earthquake loadings. Soil Dynamics and Earthquake Engineering, 1989, 3(1): 35~11。
    [67]. Park. Y. J, Aag. A. H-S. Mechanistic Seismic Damage Model for Reinforced Concrete. Journal of Structural Engineering A SCE. 1985,111 (4):722-739
    [68]. Jamshid Mohammaeli. Seismic Safety of Life Lines-an Optimum Design Method Structural Safety, 1985,2(4): 301-308。
    [69].王光远,在非平稳强地震作用下的结构反应的分析方法,土木工程学报,1964,10(1):14~22。
    [70].刘锡荟,现行规范抗震设计方法安全度的评价及工程参数的确定,地震工程与工程振动,1982,2(1):21~22。
    [71].尹之潜,李树祯等,结构抗震的可靠度与位移控制设计,地震工程与工程振动,1982,2(2):45~55。
    [72].高小旺,鲍蔼斌,地震作用的概率模型及统计参数,地震工程与工程振动,1985,5(1):13~22。
    [73].江近仁,洪峰,多层砖房的地震可靠性分析,地震工程与工程振动,1985,5(4):13~28。
    [74].江近仁,孙景江,砖结构的地震破坏模型,地震工程与工程振动,1987,7(1):20.34。
    [75].韦承基,魏琏等,结构抗震弹塑性变形可靠度分析,工程力学,1986,3(1):60~70。
    [76].欧进萍,牛获涛,杜修力,设计用随机地震动的模型及其参数确定,地震工程与工程振
    
    动,1991,11(3):45~53。
    [77].牛获涛,任利杰,改进的钢筋混凝土结构双参数地震破坏模型,地震工程与工程振动,1996,16(4):44~54。
    [78]. Wang G. Y., Wang W. Q. Fuzzy Optimum Design of A seismic Structures. Earthquake Engineering and Structural Dynamics, 1985, 13(6):827~837
    [79].江近仁,孙景江,考虑参数不确定性的结构动力可靠度分析,世界地震工程,1992,(1):30~36。
    [80].吴再光,考虑结构—地基参数变异性的地震反应分析,南京:全国第三届工程结构可靠性学术交流会议论文集,1992:290~295。
    [81].欧进萍,牛荻涛,王光远,多层非线性抗震钢结构的模糊动力可靠性分析与设计,地震工程与工程振动,1990,10(4):27~37。
    [82].陈虬,赵雷,随机参数结构的地震可靠度分析,工程力学增刊,1997:519~523。
    [83].张新培,抗震结构变形能力可靠度的时程分析法,工程力学,1996,13(4):82~88。
    [84].李杰,随机结构动力分析的扩阶系统分析方法,工程力学,1996,13(1):93~102。
    [85].袁建红,随机有限元在结构优化设计中的应用,西南交通大学硕士学位论文,2001.5。
    [86]. Combou B. Application of First Order Uncertainty Analysis in the FEM in Linear Elastic in Proceeding. Second International Conference on Application of Statistics and Probability in Soil and Structural Engineering. Press London 1971。
    [87]. Dendrou B, A. and Houstis E. N. Uncertainty Finite Element Dynamics Analytic. Report CSDTR271, Department of Civil Engineering, Purdue University West Lafayette, Indiana, 1978。
    [88]. Hisada T. and Nakagri S. Role of the Stochastic FEM in the Structural Safety Reliability in Proceedings. 4th International Conference on Structural Safety and Reliability, Japan, 1985。
    [89]. Vanmarcke E. H.. Grigoriu M.. Stochastic Finite Element Analysis of Simple Beams, ASCE. J. Eng. Mech. Div..1983, 109(5)。
    [90].朱位秋,任永坚,随机场的局部平均和随机有限元,第二届全国计算力学会议,上海,1986。
    [91]. Liu W. K. and Belytschko T. and Mani A.. Application of Probability FEM in Elastic/Plastic Dynamics and Engineering for Industry. ASCE, 1987 109。
    [92].李贤兴,陈虬,随机有限元分析及其在复合材料中的应用,工程力学,1989,6(1)。
    [93]. Liu W K.. Belytschko T., Variational Approach to Probabilistic Finite Elements. Progress Report to NASA 1984.
    [94].陈虬,刘先斌,随机有限元法及其工程应用,西南交通大学出版社,1993。
    [95].陈以新,含材料参数变异的框架剪力墙结构抗震模糊可靠度分析。华侨大学硕士论文, 1999。
    [96].邓雪松,阎维明,周云,隔震结构设计与分析软件的研制,世界地震工程,Vol.17,No.1,2001。
    [97].李桂青,曹宏,李秋胜,霍达,结构动力可靠性理论及其应用,地震出版社,北京,1993。
    [98].李宏男,吴香香,橡胶垫隔震支座结构高宽比限值研究,第24卷第2期,2003年4月。
    [99].叠层橡胶支座隔震技术规程,中国工程建设标准化协会,2001年11月1日。
    [100].高小旺,基于可靠度理论的钢筋混凝土框架建筑群的震害预测方法,中国建筑科学院
    
    工程抗震所。
    [101]. Ditlevsen O, Narrow Reliability Bounds for Structural Systems, J. Struct. Mech. ,1979, Vol. 7453~472.
    [102].王光远,谭东耀,失效相关工程系统的可靠度。地震工程与工程振动,12卷1期,1992
    [103].建筑抗震设计规范(GB50011-2001),中国建筑工业出版社,2001
    [104].赵世峰,夹层橡胶垫基础隔震结构的研究与应用,博士学位论文(东南大学),2001.6
    [105].刘小煜,建筑结构隔震技术的应用研究及隔震计算程序BIS的编制,硕士学位论文(同济大学),2002.3
    [106].叶传德,隔震技术在混凝土结构中的应用研究,硕士学位论文(同济大学),2001.10。
    [107].丘湘泉,周福霖,徐忠根,罗学海,汕头博物馆隔震设计的几个问题《第三界全国结构减震控制学术研讨会》论文集,1995。
    [108].姚谦峰,韦定国,王清敏,赵歆冬,周强,马钢,滚动隔震结构受力分析,西安建筑科技大学学报,Vol.3,1999。
    [109].宋天齐,李延年,结构隔震方向研究,特种结构Vol.1,2000。
    [110]. Roberto Villaverde. A seismic Roof Isolation System: A Feasibility Study With 13-Story Building. Proceedings of the second World Conference on Structural Control, 1998: Kyoto, Japan, p. 1657-1666.
    [111].张俊发,刘云贺,田洁,铅芯橡胶支座应用于多层框架结构加层改造的减震研究,西安建筑科技大学学报(自然科学版),Vol.2,2000。
    [112].米宏平,唐家祥,高层建筑被动混合控制的波动分析,地震工程与工程振动,Vol.18,No.3,1998.9。
    [113].赵斌,吕西林,吴敏哲,梅占馨,基础隔震建筑混合控制的变结构趋近率方法,地震工程与工程振动,Vol.19,No.3,1999.9
    [114]. Jalihal, Purnima; Utku. Senol. Active control in passively base isolated buildings subjected to low power excitations, Computers & Structures. Vol.66, January, 1998, p.211-224
    [115]. Output feedback sliding mode control of base isolated structures, Journal of the Franklin Institute, Vol-337, Aagust,2000,p.555-577.
    [116]. Isao Nishimura, Katsuyasu Sasaki, Yoshitaka Suzuki, Koji Ishii Ryuta Kataimura, Toshikazu Yamada, and Mitsuo Sakamoto, An Analytical and Experimental Study of Active Isolated Systems, Proceedings of the second World Conference on Structural Control, 1998; Kyoto, Japan, p. 1073-1082
    [117]. Taku Inaba, Hiroshi Dohi, Kenji Okuta, Taku Sato and Hlisanobu Akagi, Vibration Control of Equipment Using High Damping Rubber. Proceedings of the second World Conference on Structural Control, 1998: Kyoto, Japan, p. 1083-1092
    [118]. Erik A.Johason, Juan C.Ramallo. Billie F.Spencer, Jr. and Michael K.Sain. Intelligent base Isolation Systems. Proceedings of the second World Conference on Structural Control, 1998:Kyoto,Japan, p.367-376
    [119]. Lee-Glauser Gina J., Ahmadi Goodarz, Horta Lucas G. Integrated passive/active vibration absorber for multistory buildings. Journal of Structural Engineering,Vol.123, No.4, 1997, ASCE. p.499-504