基于液压缸内孔加工用刮削滚光技术
|
摘要
液压缸内孔加工早期主要采用镗削滚压、镗削珩磨和直接珩磨三种加工方式,但其加工效率低,不适合大批量生产。近年来,由于复合机床的发展成熟,出现了一种高效的液压缸内孔加工方法——刮削滚光,并逐步替代了传统加工,现已得到广泛应用。该文在对镗削与滚压加工进行介绍的基础上,详细阐述了刮削滚光技术。
In the early stage of internal bore machining,three methods of boring and rolling,boring honing and direct honing are used,but the machining efficiency is low and it is not suitable for mass production. In recent years,due to the maturity of the composite machine tool,an efficient method for machining the inner hole of the hydraulic cylinder,scraping and rolling,has emerged,and gradually replaces traditional processing. Now it has been widely used. In this paper,based on the introduction of boring and rolling processing,the scraping and rolling technology is described in detail.
In the early stage of internal bore machining,three methods of boring and rolling,boring honing and direct honing are used,but the machining efficiency is low and it is not suitable for mass production. In recent years,due to the maturity of the composite machine tool,an efficient method for machining the inner hole of the hydraulic cylinder,scraping and rolling,has emerged,and gradually replaces traditional processing. Now it has been widely used. In this paper,based on the introduction of boring and rolling processing,the scraping and rolling technology is described in detail.
引文
[1]臧克江.液压缸[M].北京:化学工业出版社,2010.
[2]王世清.深孔加工技术[M].西安:西安工业大学出版社,2003.
[3]战伯良,贾强,王玉梅.深孔油缸刮滚组合加工工艺[J].新技术新工艺,2012(4):20-21.
[4]杨峰.试述内孔滚压工艺原理[J].中国新技术新产品,2012(11):133-134.
[5]付群峰,张文,范敏.滚光加工技术的研究与应用[J].机械工程与自动化,2008(10):106-107.
[6]赵伟方,于德润,刘桂花,等.刮削滚光复合加工工艺浅析[J].中州煤炭,2013(9):52-53.
[7]王志远,赵勇,李福强,等.液压缸缸筒刮削变形关键技术研究与应用[J].液压气动与密封,2013(09):75-76.
[8]罗晓芳,张金涛,简玉山,等.数控刮削滚光机床的设计[J].制造技术与机床,2014(2):88-89.
[2]王世清.深孔加工技术[M].西安:西安工业大学出版社,2003.
[3]战伯良,贾强,王玉梅.深孔油缸刮滚组合加工工艺[J].新技术新工艺,2012(4):20-21.
[4]杨峰.试述内孔滚压工艺原理[J].中国新技术新产品,2012(11):133-134.
[5]付群峰,张文,范敏.滚光加工技术的研究与应用[J].机械工程与自动化,2008(10):106-107.
[6]赵伟方,于德润,刘桂花,等.刮削滚光复合加工工艺浅析[J].中州煤炭,2013(9):52-53.
[7]王志远,赵勇,李福强,等.液压缸缸筒刮削变形关键技术研究与应用[J].液压气动与密封,2013(09):75-76.
[8]罗晓芳,张金涛,简玉山,等.数控刮削滚光机床的设计[J].制造技术与机床,2014(2):88-89.