基于ANSYS的横向风板注射模具可靠性分析
|
摘要
以空调横向风板注射模具为研究对象,利用有限元分析软件ANSYS对其变形及强度可靠性进行分析,找到应力集中的区域,分析其开裂原因。结果表明:此套模具在注塑时变形较严重,塑件产品出现毛边的风险较大,壁厚超差约0.4mm;应力集中的位置主要是在定模侧模架的台阶根部,与开裂位置吻合。
The injection mould for horizontal air plate were analyzed by using ANSYS finite element analysis software.By finding the regions of stress concentration,the reasons for cracking were analyzed.The results showed that the deformation of this injection mould was serious and the plastic parts were at a greater risk of producing rough edges.The thickness of the plastic parts is 0.4mm larger than the design value.The stress concentration is mainly at the step's base of the fixed-mould side frame,and fits well with the crack location.
The injection mould for horizontal air plate were analyzed by using ANSYS finite element analysis software.By finding the regions of stress concentration,the reasons for cracking were analyzed.The results showed that the deformation of this injection mould was serious and the plastic parts were at a greater risk of producing rough edges.The thickness of the plastic parts is 0.4mm larger than the design value.The stress concentration is mainly at the step's base of the fixed-mould side frame,and fits well with the crack location.
引文
[1]翟林,韩国泰,胡海朝,等.基于Moldflow与Abaqus的注射成型及模具结构联合仿真分析[J].中国塑料,2018,32(2):128-133.
[2]王权,赵睿荣,蔡玉俊,等.基于ANSYS排水泵注射模型腔疲劳可靠性分析[J].天津职业技术师范大学学报,2014,24(1):5-8.
[3]李世保.注塑机螺杆塑化能力及能耗评价方法的研究[D].北京:北京化工大学,2008.
[4]刘斌,覃孟然,冯彦洪,等.大型注射模型腔刚度优化分析[J].模具工业,2007,33(4):1-4.
[5]廖宇航,李庆,黄志高,等.注射模结构分析中模型简化的研究[J].模具工业,2013(5):40-43.
[6]林晨.高光注塑成型数值模拟及优化[D].合肥:合肥工业大学,2014.
[2]王权,赵睿荣,蔡玉俊,等.基于ANSYS排水泵注射模型腔疲劳可靠性分析[J].天津职业技术师范大学学报,2014,24(1):5-8.
[3]李世保.注塑机螺杆塑化能力及能耗评价方法的研究[D].北京:北京化工大学,2008.
[4]刘斌,覃孟然,冯彦洪,等.大型注射模型腔刚度优化分析[J].模具工业,2007,33(4):1-4.
[5]廖宇航,李庆,黄志高,等.注射模结构分析中模型简化的研究[J].模具工业,2013(5):40-43.
[6]林晨.高光注塑成型数值模拟及优化[D].合肥:合肥工业大学,2014.