垂直发射弹头冲击力仿真研究

详细信息    查看全文 | 推荐本文 |

英文篇名：Simulation Research on Impact Force of Underwater Vertical Launching Warhead 作者：陆宇 ; 杨洋 ; 赵铮 英文作者：LU Yu;YANG Yang;ZHAO Zheng;713 Research Institute of China Shipbuilding Industry Corporation,Henan Key Laboratory of Underwater Intelligence Equipment;College of Energy and Power Engineering,Nanjing University of Science and Technology; 关键词：水下垂直发射 ; 冲击力 ; LS-DYNA ; 内压 ; 数值仿真 英文关键词：underwater vertical launch;;impact force;;LS-DYNA;;internal pressure;;numerical simulation 中文刊名：CUXI 英文刊名：Journal of Ordnance Equipment Engineering 机构：中国船舶重工集团公司第七一三研究所河南省水下智能装备重点实验室;南京理工大学能源与动力工程学院; 出版日期：2019-02-25 出版单位：兵器装备工程学报 年：2019 期：v.40;No.247 基金：国家自然科学基金项目(11302106) 语种：中文; 页：CUXI201902004 页数：3 CN：02 ISSN：50-1213/TJ 分类号：25-27

摘要

基于ANSYS/LS-DYNA建立了水下垂直发射装置头罩外层内侧内压对头罩开裂过程及冲击力影响的有限元模型,分别对有内压和无内压进行求解计算,利用后处理软件LS-PREPOST对计算结果进行对比分析。结果表明,在弹头出筒过程中,有内压和无内压工况下弹头与缓冲层之间冲击力的最大值分别为1 186 N和1 205 N,弹头与头罩外层之间冲击力的最大值分别为108 N和110 N,头罩外层内侧的均布内压对冲击力的影响很小。
        A finite element model of the underwater vertical launching device,considering the influence of the inner pressure of the outer layer of the underwater vertical launching hood on the cracking process and impact force of the hood was established based on ANSYS/LS-DYNA. The internal pressure and no internal pressure was solved separately,and the calculation results were compared and analyzed by postprocessing software LS-PREPOST. The results show that the maximum impact force between the warhead and the buffer layer under internal pressure and no internal pressure conditions is 1 186 N and 1 205 N respectively during the ejection of the warhead,and the maximum impact force between the warhead and the outer layer of the hood is 108 N and 110 N respectively. The uniform internal pressure on the inner side of the outer layer of the hood has little effect on the impact force.

引文

[1]覃东升,方勇.水下垂直发射出筒载荷响应分析[J].计算机仿真,2013,30(2):112-115.
    [2]尚书聪,孙建中,秦丽萍.潜载导弹水下发射出筒横向动力学特性研究[J].振动与冲击,2012,31(23):82-86.
    [3]陈建军.潜载导弹垂直发射对耐压壳体结构的冲击响应分析[D].哈尔滨:哈尔滨工程大学,2008.
    [4]邹鸿超.发射环境及结构参数对潜射导弹出筒载荷影响分析[D].哈尔滨:哈尔滨工业大学,2013.
    [5]张红军,陆宏志,裴胤,等.潜射导弹出筒过程的三维非定常数值模拟研究[J].水动力学研究与进展(A辑),2010,25(3):406-415.
    [6]孙船斌,马大为,朱忠领.减震垫对导弹水下垂直发射横向振动的影响[J].振动与冲击,2014,33(18):31-35.
    [7]巩明,王汉平,杨鸣,等.模拟弹水下垂直发射载荷分析[J].弹箭与制导学报,2015,35(5):41-44.
    [8]DYMENT A,FLODROPS J P,PAQUET J B,et al.Gaseous Cavity at The Base of An Underwater Projectile[J].Aerospace Science and Technology,1998(8):489-504.
    [9]KUNZ R F,LINDUA J W,GIBELING H J,et al.Unsteady,Three-dimensional Multiphase CFD Analysis of Maneuvering High Speed Supercavitating Vechicles[C]//Proceedings of the 41st Aerospace Sciences Meeting and Exhibit,Reno,Nevada:AIAA,2003:841.
    [10]YAGLA J J.Launch dynamics environment of a water piercing missile launcher[C]//Proceedings of the 24th international symposium on ballistics.New Orleans,LA:NDIA,2008:1-17.
    [11]宋旭辉,曹红松,郭向向.基于ANSYS/LS_DYNA软件的脱壳穿甲弹膛内发射过程仿真方法[J].兵器装备工程学报,2017,38(1):83-87.
    [12]谢涛,吕红超,郝陈朋.基于LS-DYNA的导弹战斗部跌落安全性分析[J].兵器装备工程学报,2018,39(8):26-29.