烟梗、烟叶配比对薄片产品得率的影响
详细信息 查看官网全文
- 英文论文题名：Research on the Effect of the Ratio on Stem and Leaf in Extraction Section for Tobacco Sheet Yield
- 论文作者：黄晶 ; 王建民 ; 孙毅 ; 孙意然
- 英文论文作者：HUANG JING ; WANG JIAN MIN ; SUN YI ; SUN YI RAN ; Zhengzhou University of Light Industry
- 年：2016
- 作者机构：郑州轻工业学院食品与生物工程学院;福建金闽再造烟叶发展有限公司;云南瑞升烟草技术(集团)有限公司;
- 论文关键词：烟草薄片 ; 烟梗 ; 烟叶 ; 原料配比 ; 产品得率
- 英文论文关键词：Tobacco Sheet ; Tobacco Stem ; Ratio of Raw Materials ; Yield
- 会议召开时间：2016-12-01
- 会议录名称：中国烟草学会2016年度优秀论文汇编——烟草工业主题
- 语种：中文
- 分类号：TS42
- 学会代码：ZGYG
- 学会名称：中国烟草学会
- 页数：6
- 文件大小：932k
- 原文格式：D
摘要
为考察造纸法再造烟叶生产过程中烟梗、烟叶原料对产品得率的影响,在福建金闽一期生产线的基础上,通过采集各牌号薄片产品烟梗、烟叶投料比及进高浓磨前皮带秤质量数据,采用一元线性回归分析生产过程中烟梗、烟叶原料配比对薄片产品得率的影响,并探讨了在提取段使用最优烟梗、烟叶原料配比情况下,梗膏、叶膏产出对生产过程物料平衡的可行性。结果表明,烟梗用量比例在50%~65%区间时,烟草纤维得率随烟梗用量比例的增加呈下降趋势。当原料全部使用烟梗时烟草纤维得率达到最小值,为45.92%,当原料全部使用烟叶原料时烟草纤维得率达到最大值为51.3%,在成本控制的前提条件下,适当的提高烟叶原料的投料比例有利于薄片得率的提升。
Stem and leaf ratio of raw materials for the yield of tobacco sheet plays an important influence in the manufacture of paper-making reconstituted tobacco.This article researched on the influence of stem and leaf ratio of raw material for the yield of tobacco sheet during the production process based on the first phase production line of Fujian Jinmin, and discussed the feasibility of stem and leaf output of material balance in the production process during the extraction process under the circumstance that using the best ratio of stem and leaf. The results show that when in range of stem dosage ratio of 50% ～ 65%, tobacco fiber yield will decline following the increase of the mentioned ratio. When material all use stem, tobacco fiber yield will reach the minimum 25.92% and when material all use pieces, tobacco fiber yield will reach the maximum 51.3%. At the same time, under the condition of the premise of cost control, appropriate increase leaf raw material charge ratio benefits to the raise of tobacco sheet yield.
Stem and leaf ratio of raw materials for the yield of tobacco sheet plays an important influence in the manufacture of paper-making reconstituted tobacco.This article researched on the influence of stem and leaf ratio of raw material for the yield of tobacco sheet during the production process based on the first phase production line of Fujian Jinmin, and discussed the feasibility of stem and leaf output of material balance in the production process during the extraction process under the circumstance that using the best ratio of stem and leaf. The results show that when in range of stem dosage ratio of 50% ～ 65%, tobacco fiber yield will decline following the increase of the mentioned ratio. When material all use stem, tobacco fiber yield will reach the minimum 25.92% and when material all use pieces, tobacco fiber yield will reach the maximum 51.3%. At the same time, under the condition of the premise of cost control, appropriate increase leaf raw material charge ratio benefits to the raise of tobacco sheet yield.
引文
[1]廖夏林,何北海,赵丽红等.低定量造纸法烟草薄片打浆及增强助剂的工艺研究[J].现代食品科技,2011,30(6):41-45
[2]陈超,田英姿.造纸法抄造甘草渣纤维烟草薄片的工艺探讨[J].食品科学,2011,30(6):50-54
[3]Hoffmann,D.,Hoffmann,I.The changing cigarette:chemical studies and Bioassays[M].In Burns,D.M.,Benowitz,N.L.(Eds),2001,159-191
[4]周红光,关平.造纸法再造烟叶抄造前设置低浓除砂器效果好[J].湖北造纸,2009,2:24-26
[5]汪华文.造纸法薄片在卷烟中的应用效果分析[J].烟草科技.2000(8):15-16
[6]方得胜.造纸法生产烟草薄片工艺探讨[J].纸和造纸,2001,(4):62-63
[7]许日鹏,苏文强,段继生.烟草薄片的开发与应用[J].上海造纸,2008,39(5):46-49
[8]凌秀菊,吴正奇,万端极.造纸法生产烟草薄片的新工艺研究[J].湖北造纸,2007(2):21-23
[9]孙德平,徐建峰,刘良才等.造纸法烟草薄片打浆工艺和助留助滤剂的研究[J].中华纸业,2010,31(22):43-47
[10]张晴川,刘孙宏,李新生等.造纸法再造烟叶涂布率与涂布工艺参数相关性研究[J].中国烟草学会工业专业委员会2011年烟草工艺学术研讨会文集[C].浙江大学出版社,2011:314-318
[11]Rodgman A,Green C R.Toxic chemicals in cigarette mainstream smoke.Hazard and hoopla[J].Beitr Tabakfor Int.,2003,20(8):481-545
[12]刘刚毅.试论我国烟草薄片技术发展战略[J].烟草科技,1995,4:2-4
[13]金闻博,戴亚.烟草化学[M].北京:清华大学出版社,1983:252-253
[14]温若愚,席年生,张大波等.不同混丝模式对烟丝掺配效果的影响[J].烟草科技,2008,9:13-16
[15]黄晶.浓缩蒸发冷凝水用于浓缩器清洗的研究[J].安徽农业科学,2012,40(25):12764-12675
[2]陈超,田英姿.造纸法抄造甘草渣纤维烟草薄片的工艺探讨[J].食品科学,2011,30(6):50-54
[3]Hoffmann,D.,Hoffmann,I.The changing cigarette:chemical studies and Bioassays[M].In Burns,D.M.,Benowitz,N.L.(Eds),2001,159-191
[4]周红光,关平.造纸法再造烟叶抄造前设置低浓除砂器效果好[J].湖北造纸,2009,2:24-26
[5]汪华文.造纸法薄片在卷烟中的应用效果分析[J].烟草科技.2000(8):15-16
[6]方得胜.造纸法生产烟草薄片工艺探讨[J].纸和造纸,2001,(4):62-63
[7]许日鹏,苏文强,段继生.烟草薄片的开发与应用[J].上海造纸,2008,39(5):46-49
[8]凌秀菊,吴正奇,万端极.造纸法生产烟草薄片的新工艺研究[J].湖北造纸,2007(2):21-23
[9]孙德平,徐建峰,刘良才等.造纸法烟草薄片打浆工艺和助留助滤剂的研究[J].中华纸业,2010,31(22):43-47
[10]张晴川,刘孙宏,李新生等.造纸法再造烟叶涂布率与涂布工艺参数相关性研究[J].中国烟草学会工业专业委员会2011年烟草工艺学术研讨会文集[C].浙江大学出版社,2011:314-318
[11]Rodgman A,Green C R.Toxic chemicals in cigarette mainstream smoke.Hazard and hoopla[J].Beitr Tabakfor Int.,2003,20(8):481-545
[12]刘刚毅.试论我国烟草薄片技术发展战略[J].烟草科技,1995,4:2-4
[13]金闻博,戴亚.烟草化学[M].北京:清华大学出版社,1983:252-253
[14]温若愚,席年生,张大波等.不同混丝模式对烟丝掺配效果的影响[J].烟草科技,2008,9:13-16
[15]黄晶.浓缩蒸发冷凝水用于浓缩器清洗的研究[J].安徽农业科学,2012,40(25):12764-12675