变速器齿轮敲击参数灵敏度分析

详细信息    查看全文 | 推荐本文 |

英文篇名：Sensitivity Analysis of Gear Rattle Parametric of Transmission 作者：石晓辉 ; 熊秀文 ; 郭栋 ; 郑光泽 ; 柳培海 ; 张海林 英文作者：Shi Xiaohui;Xiong Xiuwen;Guo Dong;Zheng Guangze;Liu Peihai;Zhang Hailin;Key Laboratory of Advanced Manufacturing Technology for Automobile Parts of Ministry of Education,Chongqing University of Technology;College of Vehicle Engineering,Chongqing University of Technology; 关键词：变速器 ; 敲击 ; 评价指标 ; 灵敏度 英文关键词：Transmission;;Gear rattle;;Evaluation index;;Sensitivity 中文刊名：JXCD 英文刊名：Journal of Mechanical Transmission 机构：重庆理工大学汽车零部件先进制造技术教育部重点实验室;重庆理工大学车辆工程学院; 出版日期：2018-03-15 出版单位：机械传动 年：2018 期：v.42;No.255 基金：重庆市教委科学技术研究项目(KJ1600914);; 重庆理工大学研究生创新基金(YCX2016211) 语种：中文; 页：JXCD201803022 页数：7 CN：03 ISSN：41-1129/TH 分类号：106-111+116

摘要

以某款手动变速器为研究对象,基于SIMdrive软件,搭建考虑输入轴转速波动、齿侧间隙、空套齿轮转动惯量及拖拽力矩等影响因素的变速器齿轮敲击仿真分析模型,计算各空套齿轮的角速度及各非承载齿轮对的啮合力。进行变速器齿轮敲击台架试验,测得空套齿轮转速信号,验证仿真分析模型的有效性。从冲击能量的角度出发,选取非承载齿轮对的啮合力对时间的导数为敲击评价指标(Jerk指标),并用向前差分法求解各个工况下的Jerk指标。分别对转速波动、齿侧间隙、空套齿轮转动惯量及拖拽力矩这4个参数求偏导,从而求得各参数对变速器齿轮敲击的灵敏度规律。发现转速波动对敲击的灵敏度始终为正,转速波动在40 r/min时,对敲击的影响开始陡增。齿侧间隙小于0.1 mm时,敲击灵敏度为正,大于0.1 mm时为负。空套齿轮转动惯量对敲击的灵敏度始终为负,在转动惯量大于0.000 6 kg·m~2时,敲击灵敏度值几乎不变,转动惯量的改变对敲击的影响并不明显。拖拽力矩小于0.6 N·m时,敲击灵敏度为负,大于0.6 N·m时为正,在0.2~0.3 N·m之间时,拖拽力矩对敲击的影响并不明显。
        Taking a manual transmission as research object,a simulation analysis model of transmission gear rattle is conducted by using the SIMdrive software,this model considering the influencing factors such as input shaft speed fluctuation,clearance,inertia of loose gear and drag torque,and these influence factors are used to calculate the angular velocity of each loose gear and the engaging force of each idler gear pair. The transmission gear rattle is tested and the loose gear speed signals are measured to verify the effectiveness of the simulation analysis model. From the point of view of the impact energy,the derivative of the idler gear on the meshing force is taken as the rattle index( Jerk index),and using the forward difference method to solve the Jerk index under various conditions. The partial derivative of the four parameters of speed fluctuation,clearance,inertia of loose gear and drag torque are obtained respectively,and the sensitivity of each parameter to the transmission gear rattle is obtained. It is found that the sensitivity of the speed fluctuation to the rattle is always positive,and when the speed fluctuates at 40 r/min,the influence on the gear rattle starts to increase sharply.When the clearance is less than 0. 1 mm,the rattle sensitivity is positive,more than 0. 1 mm when the negative.The sensitivity of the inertia of loose gear is always negative,and when the inertia is more than 0. 000 6 kgm~2,the rattle sensitivity value is almost unchanged and the effect of the change in inertia on the gear rattle is not noticeable. When the drag torque is less than 0. 6 N·m,the rattle sensitivity is negative,more than 0. 6 N·m when the positive,and at 0. 2 N·m to 0. 3 N·m between the drag torque on the gear rattle is not noticeable.

引文

[1]NAUNHEIMER H,BERTSCHE B,RYBORZ J,et al.Automotive transmissions:fundamentals,selection,design and application[M].Berlin:Springer Science&Business Media,2010:269-270.
    [2]项小雷,陈德鑫,李松松.双中间轴式手动变速器齿轮敲击噪声理论及试验研究[J].汽车技术,2014(11):1-6.
    [3]ROBINETTE D,RANDALL S,BEIKMANN,et al.Characterizing the onset of manual transmission gear rattle part i:experimental results[J].SAE International Journal of Passenger Cars-Mechanical Systems,2009,2(1):1352-1364.
    [4]ROBINETTE D,RANDALL S,BEIKMANN,et al.Characterizing the onset of manual transmission gear rattle part ii:analytical results[J].SAE International Journal of Passenger Cars-Mechanical Systems,2009,2(1):1365-1376.
    [5]WANG M Y,MANOJ R,ZHAO W,等.汽车手动变速箱的齿轮敲击模拟和分析[J].传动技术,2002,16(4):27-42.
    [6]WANG M Y,ZHAO W,MANOJ R.Numerical modelling and analysis of automotive transmission rattle[J].Journal of Vibration and Control,2002,8(7):921-943.
    [7]SAKAI T,DOI Y,YAMAMOTO K,et al.Theoretical and experimental analysis of rattling noise of automotive gearbox[J].Society of Automotive Engineers Preprint,1981:810773.DOI:https://doi.org/10.4271/810773.
    [8]SINGH R.Analysis of automotive neutral gear rattle[J].Journal of Sound&Vibration,1989,131(2):177-196.
    [9]PADMANABHAN C,ROOK T E,SINGH R.Modeling of automotive gear rattle phenomenon:state of the art[J].SAE Technical Paper,1995:951316.
    [10]BILE Y,GONDHALEKAR A,KUMBHAR M.Studies on neutral gear rattle in early stage design[J].SAE Technical Papers,2013:2013-26-0109.
    [11]OTTEWILL J R,NEILD S A,WILSON R E.Intermittent gear rattle due to interactions between forcing and manufacturing errors[J].Journal of Sound&Vibration,2009,321(3):913-935.
    [12]BAUMANN A,BERTSCHE B.Experimental study on transmission rattle noise behaviour with particular regard to lubricating oil[J].Journal of Sound and Vibration,2015,341:195-205.
    [13]YAKOUB R Y,CORRADO M,FORCELLI A,et al.Prediction of system-level gear rattle using multibody and vibro-acoustic techniques[J].SAE Transactions Paper,2004:2004-32-0063.
    [14]吴光强,吴虎威,李迪.汽车变速器齿轮敲击动力学问题研究综述[J].同济大学学报(自然科学版),2016,44(2):276-285.