QEPAS系统中石英音叉模态仿真计算与研究
|
摘要
对石英音叉增强型光声光谱(QEPAS)系统中常用的石英音叉进行了有限元模态计算,获得石英音叉前6阶振型与模态频率,认知了第4阶对称摆动振型为有效振动,利用单因素法分析了石英音叉的音臂长度l1、音臂宽度w1、音臂厚度t、音臂切角θ、音臂圆孔直径d及音臂圆孔高度h对低阶有效共振频率(Fre)的影响,敏感度依次为:l1> w1>d>θ>t>h,考虑实际设计情形,筛选出了l1,w1,d与h四个石英音叉设计变量,采用Box-Behnken实验设计方案与RSM(response surface methodology)方法,以Fre为函数目标,建立l1,w1,d与h的二次回归响应面模型,得到了参数之间的交互作用,利用Design-Expert软件对响应面模型进行设计参数反求,结果表明,在15 000 Hz≤Fre≤25 000 Hz计算区域内误差较小,基本满足QEPAS系统的计算需求,所提出的研究与设计方法具有一定通用性,可为QEPAS系统中石英音叉结构参数设计提供参考。
The finite element modes of the quartz tuning fork in the Quartz Enhanced Photoacoustic Spectroscopy(QEPAS)system were calculated and the first 6modes and modal frequencies of the quartz tuning fork were obtained.The 4th order symmetrically oscillating vibration mode was recognized as an effective vibration.Single factor method was used to analyze the effects of fork's arm length l1,fork's arm width w1,fork's arm thickness t,fork's arm cutting angleθ,fork's arm diameter dand fork's arm round hole height hon low effective resonance frequency(Fre).The results of the sensitivity sensitivity were as follows:l1>w1>d>θ>t>h.Considering the actual design situation,four design parameters of quartz tuning fork l1,w1,dand h were screened.Using Box-Behnken experimental design and RSM(Response Surface Methodology)method,Fre was set as a function target to establish l1,w1,dand hquadratic regression response surface model,and get the interaction between the parameters.The Design-Expert software was used to inverse the design parameters of the response surface model.The results showed that the error in the calculation area of 15 000Hz≤Fre≤25 000 Hz is small,and basically meets the calculation requirements of QEPAS system.The proposed research and design methods have some generality,which can provide references for the design of quartz tuning fork structure in QEPAS system.
The finite element modes of the quartz tuning fork in the Quartz Enhanced Photoacoustic Spectroscopy(QEPAS)system were calculated and the first 6modes and modal frequencies of the quartz tuning fork were obtained.The 4th order symmetrically oscillating vibration mode was recognized as an effective vibration.Single factor method was used to analyze the effects of fork's arm length l1,fork's arm width w1,fork's arm thickness t,fork's arm cutting angleθ,fork's arm diameter dand fork's arm round hole height hon low effective resonance frequency(Fre).The results of the sensitivity sensitivity were as follows:l1>w1>d>θ>t>h.Considering the actual design situation,four design parameters of quartz tuning fork l1,w1,dand h were screened.Using Box-Behnken experimental design and RSM(Response Surface Methodology)method,Fre was set as a function target to establish l1,w1,dand hquadratic regression response surface model,and get the interaction between the parameters.The Design-Expert software was used to inverse the design parameters of the response surface model.The results showed that the error in the calculation area of 15 000Hz≤Fre≤25 000 Hz is small,and basically meets the calculation requirements of QEPAS system.The proposed research and design methods have some generality,which can provide references for the design of quartz tuning fork structure in QEPAS system.
引文
[1] Kosterev A A,Tittel F K,Curl R F,et al.Optics Letters,2002,27(21):1902.
[2] Ma Y,Yu X,Yu G,et al.Applied Physics Letters,2015,107(2):1993.
[3] MA Yu-fei,YU Guang,ZHANG Jing-bo,et al(马欲飞,于光,张静波,等).Spectroscopy and Spectral Analysis(光谱学与光谱分析),2015,35(11):3003.
[4] Dong L,Wu H,Zheng H,et al.Optics Letters,2014,39(8):2479.
[5] Zheng H,Dong L,Sampaolo A,et al.Applied Physics Letters,2016,109(11):1902.
[6] Wu H,Yin X,Dong L,et al.Applied Physics Letters,2017,110(12):121104.
[7] Liu K,Guo X,Yi H,et al.Optics Letters,2009,34(10):1594.
[8] Yi H,Liu K,Chen W,et al.Optics Letters,2011,36(4):481.
[9] WANG Gui-shi,YI Hong-ming,CAI Ting-dong,et al(王贵师,易红明,蔡廷栋,等).Acta Physica Sinica(物理学报),2012,61(12):120701.
[10] ZHANG Zhou-qiang,JIA Shu-hai,MA Bin-shan(张周强,贾书海,马斌山).Journal of Xi’an Jiaotong University(西安交通大学学报),2014,48(7):96.
[11] GU Hai-ming,ZHOU Yong-jun(顾海明,周勇军).Theory and Application of Mechanical Vibration(机械振动理论与应用).Nanjing:Southeast University Press(南京:东南大学出版社),2007.
[12] Usher M B.Catena,2001,42(2-4):375.
[13] HE-Wei,XUE Wei-dong,TANG Bin(何为,薛卫东,唐斌).Optimizing Experimental Design Method and Data Analysis(优化实验设计方法及数据分析).Beijing:Chemical Industry Press(北京:化学工业出版社),2012.218.
[2] Ma Y,Yu X,Yu G,et al.Applied Physics Letters,2015,107(2):1993.
[3] MA Yu-fei,YU Guang,ZHANG Jing-bo,et al(马欲飞,于光,张静波,等).Spectroscopy and Spectral Analysis(光谱学与光谱分析),2015,35(11):3003.
[4] Dong L,Wu H,Zheng H,et al.Optics Letters,2014,39(8):2479.
[5] Zheng H,Dong L,Sampaolo A,et al.Applied Physics Letters,2016,109(11):1902.
[6] Wu H,Yin X,Dong L,et al.Applied Physics Letters,2017,110(12):121104.
[7] Liu K,Guo X,Yi H,et al.Optics Letters,2009,34(10):1594.
[8] Yi H,Liu K,Chen W,et al.Optics Letters,2011,36(4):481.
[9] WANG Gui-shi,YI Hong-ming,CAI Ting-dong,et al(王贵师,易红明,蔡廷栋,等).Acta Physica Sinica(物理学报),2012,61(12):120701.
[10] ZHANG Zhou-qiang,JIA Shu-hai,MA Bin-shan(张周强,贾书海,马斌山).Journal of Xi’an Jiaotong University(西安交通大学学报),2014,48(7):96.
[11] GU Hai-ming,ZHOU Yong-jun(顾海明,周勇军).Theory and Application of Mechanical Vibration(机械振动理论与应用).Nanjing:Southeast University Press(南京:东南大学出版社),2007.
[12] Usher M B.Catena,2001,42(2-4):375.
[13] HE-Wei,XUE Wei-dong,TANG Bin(何为,薛卫东,唐斌).Optimizing Experimental Design Method and Data Analysis(优化实验设计方法及数据分析).Beijing:Chemical Industry Press(北京:化学工业出版社),2012.218.
© 2004-2018 中国地质图书馆版权所有 京ICP备05064691号 京公网安备11010802017129号 地址：北京市海淀区学院路29号 邮编：100083 电话：办公室：(+86 10)66554848；文献借阅、咨询服务、科技查新：66554700 |