Experimental investigation on punching resistance of R-UHPFRC–RC composite slabs

详细信息    查看全文

• 作者：Malena Bastien-Masse ; Eugen Brühwiler
• 关键词：Composite slab ; Punching shear ; Ultra ; high performance fiber reinforced cement ; based composite (UHPFRC) ; Strengthening ; Near interface crack ; Deformation capacity
• 刊名：Materials and Structures
• 出版年：2016
• 出版时间：May 2016
• 年：2016
• 卷：49
• 期：5
• 页码：1573-1590
• 全文大小：1,546 KB
• 参考文献：1.Broms CE (2000) Elimination of flat plate punching failure mode. ACI Struct J 97(1):94–101
  2.Habel K, Denarié E, Brühwiler E (2006) Structural response of elements combining ultrahigh-performance fiber-reinforced concretes and reinforced concrete. J Struct Eng 13(11):1793–1800CrossRef
  3.Denarié E, Brühwiler E (2011) Strain hardening of ultra-high performance fibre reinforced concrete: deformability versus strength optimization. Int J Restor Build Monum 12(6):397–410
  4.Brühwiler E, Denarié E (2013) Rehabilitation and strengthening of concrete structures using ultra-high performance fiber reinforced concrete. Struct Eng Int 23(4):450–457CrossRef
  5.Oesterlee C (2010) Structural response of reinforced UHPFRC and RC composite members. Dissertation, EPFL, Lausanne
  6.Habel K, Denarié E, Brühwiler E (2007) Experimental investigation of composite ultra-high-performance fiber reinforced concrete and conventional concrete members. ACI Struct J 104(1):93–101
  7.Noshiravani T, Brühwiler E (2013) Experimental investigation on R-UHPFRC–RC composite beams subjected to combined bending and shear. ACI Struct J 110(2):251–261
  8.Bastien-Masse M (2014) Punching test on R-UHPFRC–RC composite slabs without shear reinforcement. Test report. MCS, EPFL, Lausanne
  9.Guandalini S, Burdet OL, Muttoni A (2009) Punching tests of slabs with low reinforcement ratios. ACI Struct J 106(1):87–95
  10.Muttoni A (2008) Punching strength of reinforced concrete slabs without transverse reinforcement. ACI Struct J 105(4):440–450
  11.Theodorakopoulos DD, Swamy RN (2002) Ultimate punching shear strength analysis of slab-column connections. Cem Concr Compos 24:509–521CrossRef
  12.Menétrey Ph (2002) Synthesis of punching failure in reinforced concrete. Cem Concr Compos 24:497–507CrossRef
  13.Koppitz R, Kenel A, Keller T (2013) Punching shear of RC flat slabs—review of analytical models for new and strengthening of existing slabs. Eng Struct 52:123–130CrossRef
  14.Amsler M, Thoma K, Heinzmann D (2014) Punching slab strengthened with an additional concrete layer—test and recalculations. Beton- und Stahlbetonbau 109(6):394–402CrossRef
  15.Chen C-C, Li C-Y (2005) Punching shear strength of reinforced concrete slabs strengthened with glass fiber-reinforced polymer laminates. ACI Struct J 102(4):535–542
  16.Esfahani MR, Kianoush MR, Moradi AR (2009) Punching shear strength of interior slab-column connections strengthened with carbon fiber reinforced polymer sheets. Eng Struct 31:1535–1542CrossRef
  17.Harajli MH, Soudki KA (2003) Shear strengthening of interior slab-column connections using fiber-reinforced polymer sheets. J Compos Constr 7(2):145–153CrossRef
  18.Sharaf MH, Soudki KA, Van Dusen M (2006) CFRP strengthening for punching shear of interior slab-column connections. J Compos Constr 10(5):410–418CrossRef
  19.Wuest J (2007) Comportement structural des bétons de fibres ultra performants en traction dans des éléments composés. Dissertation, EPFL, Lausanne
  20.Guidotti R (2010) Poinçonnement des planchers-dalles avec colonnes superposées fortement sollicitées, Dissertation, EPFL, Lausanne
  21.Clément T, Pinho Ramos A, Fernández Ruiz M, Muttoni A (2014) Influence of prestressing on the punching strength of post-tensionned slabs. Eng Struct 72:59–69CrossRef
  22.Lips S, Fernandez Ruiz M, Muttoni A (2012) Experimental investigation on punching strength and deformation capacity of shear-reinforced slabs. ACI Struct J 109(6):889–900
  23.Rossi P (1997) High performance multimodal fiber reinforced cement composites (HPMFRCC): the LCPC experience. ACI Mater J 94(6):478–483
  24.Rossi P, Arca A, Parant E, Fakhri P (2005) Bending and compressive behaviors of a new cement composite. Cem Concr Res 35:27–33CrossRef
  25.Fernández Ruiz M, Mirzaei Y, Muttoni A (2013) Post-punching behavior of flat slabs. ACI Struct J 110(5):801–811
  26.Habibi F, Cook WD, Mitchell D (2014) Predicting post-punching shear response of slab-column connections. ACI Struct J 111(1):123–134
  
• 作者单位：Malena Bastien-Masse (1)
  Eugen Brühwiler (1)
  
  1. École Polytechnique Fédérale de Lausanne, Lausanne, Switzerland
  
• 刊物类别：Engineering
• 刊物主题：Structural Mechanics
  Theoretical and Applied Mechanics
  Mechanical Engineering
  Operating Procedures and Materials Treatment
  Civil Engineering
  Building Materials
  
• 出版者：Springer Netherlands
• ISSN：1871-6873

文摘

An effective method to strengthen existing reinforced concrete (RC) structures is to add a thin layer of ultra-high performance fiber reinforced cement-based composite (UHPFRC), with or without steel rebars, over the concrete slab to create a composite element. It was demonstrated by previous test series that this method increases rigidity, bending and shear strength of one-way RC members. This paper presents the results of punching tests on six composite slabs without transverse reinforcement. The parameters of the tests included the thickness of the UHPFRC layer and the amount of reinforcement in it. All slabs failed in punching mode with a drop in resistance after the maximum resistance was measured. For a layer of 50 mm of UHPFRC, the normalised resistance was at least 1.69 times greater than the normalised resistance of the RC reference slab. The layer of UHPFRC increased the rigidity of the slab and provided added shear resistance to the cracked RC section by out of plane bending. By doing so, it allowed more deformation to take place in the RC section before punching failure. This results in rotations and deflections at maximum resistance similar to what was observed for the reference RC slab.