牙种植体生物力学评价研究进展
|
摘要
牙种植体的生物力学特性一直是口腔种植领域的研究热点。避免局部应力集中、使咬合力合理分布是保证种植体周围支持组织健康,并能够长期行使功能的必要条件。本文就牙种植体的生物力学研究方法及评价指标做一综述。
Biomechanical properties of dental implants have been a hot research field of oral implantology. To avoid local stress concentration and to ensure that the bite force distribution is reasonable is the necessary conditions of the peri-implant support organization for health and for long-term function.This article reviewed the biomechanical research methods and evaluation indexes of dental implants.
Biomechanical properties of dental implants have been a hot research field of oral implantology. To avoid local stress concentration and to ensure that the bite force distribution is reasonable is the necessary conditions of the peri-implant support organization for health and for long-term function.This article reviewed the biomechanical research methods and evaluation indexes of dental implants.
引文
[1]Hollweg H,Jacques LB,da Silva MM,et al.Deformation of implant abutments after framework connection using strain gauges[J].J Oral Implantol,2012,38(2):125-132.
[2]Abreu CW,Nishioka RS,Balducci I,et al.Straight and offset implant placement under axial and nonaxial loads in implant-supported prostheses:strain gauge analysis[J].J Prosthodont,2012,21(7):535-539.
[3]Anitua E,Tapia R,Luzuriaga F,et al.Influence of implant length,diameter,and geometry on stress distribution:a finite element analysis[J].Int J Periodontics Restorative Dent,2010,30(1):89-95.
[4]佘文珺,马璐,何嘉菁,等.磁性附着体下颌种植覆盖义齿牙槽骨的三维光弹应力分析[J].临床口腔医学杂志,2011,27(7):392-395.
[5]彭艳,焦婷,金文忠,等.舌向集中牙合全口义齿应力分布的光弹性研究(下颌种植覆盖义齿加载)[J].上海交通大学学报(医学版),2012,32(3):317-320.
[6]Pellizzer E,Falcón-Antenucci RM,de Carvalho PS,et al.Photoelastic analysis of the influence of platform switching on stress distribution in implants[J].J Oral Implantol,2010,34(6):419-424.
[7]Bernardes SR,de Araújo CA,Neto AJ,et al.Photoelastic analysis of stress patterns from different implant-abutment interfaces[J].Int J Oral Maxillofac Implants,2009,24(5):781-789.
[8]Karl M,Wichmann MG,Winter W,et al.Influence of fixation mode and superstructure span upon strain development of implant fixed partial dentures[J].J Prosthodont,2008,17(1):3-8.
[9]Tiossi R,Lin L,Rodrigues RC,et al.Digital image correlation analysis of the load transfer by implant-supported restorations[J].J Biomech,2011,44(6):1008-1013.
[10]Li J,Fok AS,Satterthwaite J,et al.Measurement of the full-field polymerization shrinkage and depth of cure of dental composites using digital image correlation[J].Dent Mater,2009,25(5):582-588.
[11]Tiossi R,Lin L,Conrad HJ,et al.A digital image correlation analysis on the influence of crown material in implant-supported prostheses on bone strain distribution[J].J Prosthodont Res,2012,56(1):25-31.
[12]Clelland NL,Yilmaz B,Seidt JD.Three-dimensional image correlation analyses for strains generated by cement and screw-retained implant prostheses.[J].Clin Implant Dent Relat Res,2013,15(2):271-282.
[13]耿黎,张东升,韩栋伟,等.数字图像相关技术对烤瓷熔附金属冠破坏形式的研究[J].同济大学学报·医学版,2007,28(2):84-88.
[14]Tsai YT,Wang KS,Woo JC.Fatigue life and reliability evaluation for dental implants based on computer simulation and limited test data[J].P I Mech Eng C-J MEC,2013,227(3):554-564.
[15]Meijer HJ,Kuiper JH,Starmans FJ,et al.Stress distribution around dental implants:influence of superstructure,length of implants,and height of mandible[J].J Prosthet Dent,1992,68(1):96-102.
[16]Toniollo MB,Macedo AP,Rodrigues RC,et al.Three-dimensional finite element analysis of stress distribution on different bony ridges with different lengths of morse taper implants and prosthesis dimensions[J].J Craniofac Surg,2012,23(6):1888-1892.
[17]张士剑.有限元法在种植修复中应用进展[J].中国实用口腔科杂志,2010,3(11):691-694.
[18]Martini AP,Freitas AC,Rocha EP,et al.Straight and angulated abutments in platform switching:influence of loading on bone stress by three-dimensional finite element analysis[J].J Craniofac Surg,2012,23(2):415-418.
[19]陈轶珺.氧化锆全瓷角度基台的三维有限元应力分析[J].口腔医学研究,2008,24(3):317-319.
[20]张士剑,包晓亮,蔺增,等.不同种植方式修复下颌后部游离缺失的三维有限元分析[J].口腔医学,2011,31(1):12-15.
[21]Alvarez K,Fukuda M,Yamamoto O.Titanium implants after alkali heating treatment with a[Zn(OH)4]2 complex:analysis of interfacial bond strength using push-out tests[J].Clin Implant Dent Relat Res,2010,12(Suppl 1):e114-125.
[22]Renz RP,Cunha A,Wantowski G,et al.Osseointegration evaluation of treated surfaces of titanium implants applying tensile pull-out test[J].Rev Clin Pesq Odontol,2007,3(3):149-157.
[23]Seong WJ,Grami S,Jeong SC,et al.Comparison of push-in versus pull-out tests on bone-implant interfaces of rabbit tibia dental implant healing model[J].Clin Implant Dent Relat Res,2013,15(3):460-469.
[24]Beer A,Gahleitner A,Holm A,et al.Correlation of insertion torques with bone mineral density from dental quantitative CT in the mandible[J].Clin Oral Implants Res,2003,14(5):616-620.
[25]Aparicio C,Rangert B,Sennerby L.Immediate/early loading of dental implants:a report from the Sociedad Espanola de Implants World Congress consensus meeting in Barcelona,Spain,2002[J].Clin Implant Dent Relat Res,2003,5(1):57-60.
[26]Trisi P,Berardi D,Paolantonio M,et al.Primary stability,insertion torque,and bone density of conical implants with internal hexagon:is there a relationship?[J].J Craniofac Surg,2013,24(3):841-844.
[27]Gahlert M,R?hling S,Wieland M,et al.A comparison study of the osseointegration of zirconia and titanium dental implants:a biomechanical evaluation in the maxilla of pigs[J].Clin Implant Dent Relat Res,2010,12(4):297-305.
[28]Al-Jetaily S,Al-dosari AA.Assessment of OsstellTM and Periotest? systems in measuring dental implant stability(in vitro study)[J].Saudi Dent J,2011,23(1):17-21.
[29]Simunek A,Vokurkova J,Kopecka D,et al.Evaluation of stability of titanium and hydroxyapatite-coated osseointegrated dental implants:a pilot study[J].Clin Oral Implants Res,2002,13(1):75-79.
[30]Nkenke E,HahnM,Weinzierl K,et al.Implant stability and histomorphometry:a correlation study in human cadavers using stepped cylinder implants[J].Clin Oral Implants Res,2003,14(5):601-609.
[2]Abreu CW,Nishioka RS,Balducci I,et al.Straight and offset implant placement under axial and nonaxial loads in implant-supported prostheses:strain gauge analysis[J].J Prosthodont,2012,21(7):535-539.
[3]Anitua E,Tapia R,Luzuriaga F,et al.Influence of implant length,diameter,and geometry on stress distribution:a finite element analysis[J].Int J Periodontics Restorative Dent,2010,30(1):89-95.
[4]佘文珺,马璐,何嘉菁,等.磁性附着体下颌种植覆盖义齿牙槽骨的三维光弹应力分析[J].临床口腔医学杂志,2011,27(7):392-395.
[5]彭艳,焦婷,金文忠,等.舌向集中牙合全口义齿应力分布的光弹性研究(下颌种植覆盖义齿加载)[J].上海交通大学学报(医学版),2012,32(3):317-320.
[6]Pellizzer E,Falcón-Antenucci RM,de Carvalho PS,et al.Photoelastic analysis of the influence of platform switching on stress distribution in implants[J].J Oral Implantol,2010,34(6):419-424.
[7]Bernardes SR,de Araújo CA,Neto AJ,et al.Photoelastic analysis of stress patterns from different implant-abutment interfaces[J].Int J Oral Maxillofac Implants,2009,24(5):781-789.
[8]Karl M,Wichmann MG,Winter W,et al.Influence of fixation mode and superstructure span upon strain development of implant fixed partial dentures[J].J Prosthodont,2008,17(1):3-8.
[9]Tiossi R,Lin L,Rodrigues RC,et al.Digital image correlation analysis of the load transfer by implant-supported restorations[J].J Biomech,2011,44(6):1008-1013.
[10]Li J,Fok AS,Satterthwaite J,et al.Measurement of the full-field polymerization shrinkage and depth of cure of dental composites using digital image correlation[J].Dent Mater,2009,25(5):582-588.
[11]Tiossi R,Lin L,Conrad HJ,et al.A digital image correlation analysis on the influence of crown material in implant-supported prostheses on bone strain distribution[J].J Prosthodont Res,2012,56(1):25-31.
[12]Clelland NL,Yilmaz B,Seidt JD.Three-dimensional image correlation analyses for strains generated by cement and screw-retained implant prostheses.[J].Clin Implant Dent Relat Res,2013,15(2):271-282.
[13]耿黎,张东升,韩栋伟,等.数字图像相关技术对烤瓷熔附金属冠破坏形式的研究[J].同济大学学报·医学版,2007,28(2):84-88.
[14]Tsai YT,Wang KS,Woo JC.Fatigue life and reliability evaluation for dental implants based on computer simulation and limited test data[J].P I Mech Eng C-J MEC,2013,227(3):554-564.
[15]Meijer HJ,Kuiper JH,Starmans FJ,et al.Stress distribution around dental implants:influence of superstructure,length of implants,and height of mandible[J].J Prosthet Dent,1992,68(1):96-102.
[16]Toniollo MB,Macedo AP,Rodrigues RC,et al.Three-dimensional finite element analysis of stress distribution on different bony ridges with different lengths of morse taper implants and prosthesis dimensions[J].J Craniofac Surg,2012,23(6):1888-1892.
[17]张士剑.有限元法在种植修复中应用进展[J].中国实用口腔科杂志,2010,3(11):691-694.
[18]Martini AP,Freitas AC,Rocha EP,et al.Straight and angulated abutments in platform switching:influence of loading on bone stress by three-dimensional finite element analysis[J].J Craniofac Surg,2012,23(2):415-418.
[19]陈轶珺.氧化锆全瓷角度基台的三维有限元应力分析[J].口腔医学研究,2008,24(3):317-319.
[20]张士剑,包晓亮,蔺增,等.不同种植方式修复下颌后部游离缺失的三维有限元分析[J].口腔医学,2011,31(1):12-15.
[21]Alvarez K,Fukuda M,Yamamoto O.Titanium implants after alkali heating treatment with a[Zn(OH)4]2 complex:analysis of interfacial bond strength using push-out tests[J].Clin Implant Dent Relat Res,2010,12(Suppl 1):e114-125.
[22]Renz RP,Cunha A,Wantowski G,et al.Osseointegration evaluation of treated surfaces of titanium implants applying tensile pull-out test[J].Rev Clin Pesq Odontol,2007,3(3):149-157.
[23]Seong WJ,Grami S,Jeong SC,et al.Comparison of push-in versus pull-out tests on bone-implant interfaces of rabbit tibia dental implant healing model[J].Clin Implant Dent Relat Res,2013,15(3):460-469.
[24]Beer A,Gahleitner A,Holm A,et al.Correlation of insertion torques with bone mineral density from dental quantitative CT in the mandible[J].Clin Oral Implants Res,2003,14(5):616-620.
[25]Aparicio C,Rangert B,Sennerby L.Immediate/early loading of dental implants:a report from the Sociedad Espanola de Implants World Congress consensus meeting in Barcelona,Spain,2002[J].Clin Implant Dent Relat Res,2003,5(1):57-60.
[26]Trisi P,Berardi D,Paolantonio M,et al.Primary stability,insertion torque,and bone density of conical implants with internal hexagon:is there a relationship?[J].J Craniofac Surg,2013,24(3):841-844.
[27]Gahlert M,R?hling S,Wieland M,et al.A comparison study of the osseointegration of zirconia and titanium dental implants:a biomechanical evaluation in the maxilla of pigs[J].Clin Implant Dent Relat Res,2010,12(4):297-305.
[28]Al-Jetaily S,Al-dosari AA.Assessment of OsstellTM and Periotest? systems in measuring dental implant stability(in vitro study)[J].Saudi Dent J,2011,23(1):17-21.
[29]Simunek A,Vokurkova J,Kopecka D,et al.Evaluation of stability of titanium and hydroxyapatite-coated osseointegrated dental implants:a pilot study[J].Clin Oral Implants Res,2002,13(1):75-79.
[30]Nkenke E,HahnM,Weinzierl K,et al.Implant stability and histomorphometry:a correlation study in human cadavers using stepped cylinder implants[J].Clin Oral Implants Res,2003,14(5):601-609.