精轧和吐丝温度对SCM435线材氧化铁皮物相结构的影响
详细信息    查看全文 | 推荐本文 |
  • 英文篇名:Effect of Finish Rolling and Spinning Temperature on Phase Structure of Iron Oxide Skin of SCM435 Wire Rod
  • 作者:王宁涛 ; 李世琳 ; 阮士朋 ; 王利军
  • 英文作者:Wang Ningtao;Li Shilin;Ruan Shipeng;Wang Lijun;Hebei Engineering Research Center For Wire Rod;Xingtai Iron & Steel Co.Ltd.;
  • 关键词:氧化铁皮 ; SCM435 ; 电子背散射衍射 ; 物相
  • 英文关键词:Oxide Scale;;SCM435;;Electron Backscattered Diffraction;;Scale Phase
  • 中文刊名:TSGA
  • 英文刊名:Special Steel
  • 机构:河北省线材工程技术研究中心;邢台钢铁有限责任公司;
  • 出版日期:2019-07-24
  • 出版单位:特殊钢
  • 年:2019
  • 期:v.40;No.228
  • 语种:中文;
  • 页:TSGA201904003
  • 页数:3
  • CN:04
  • ISSN:42-1243/TF
  • 分类号:8-10
摘要
线材的氧化铁皮起着保护线材免锈蚀的作用,但是也需要在酸洗时容易除去。影响铁皮除去或结合力的主要是铁皮的厚度和其物相结构。通过对不同轧制条件下的氧化铁皮厚度、物相结构进行检测分析,研究了精轧温度和吐丝温度对φ12 mm SCM435氧化铁皮物相结构的影响。研究表明,随着精轧温度或吐丝温度的升高,SCM435线材的氧化铁皮厚度均会增加,且在800-900℃短时间就会生成较厚(约20μm)的氧化铁皮;由于Cr的氧化选择性,精轧温度在870℃以上,吐丝温度在810℃以上时,随精轧温度或吐丝温度升高,氧化铁皮中FeO比例提高;但是吐丝温度高于860℃后,物相结构的变化趋缓,FeO的比例变化不大。
        Oxide Scale of wire plays a role to protect wire from rust,but it also needs to be removed easily when pickling.The thickness of iron scale and its phase structure are the main factors affecting the removal or adhesion of iron scale.The effects of finishing rolling temperature and spinning temperature on the phase structure ofΦ12 mm SCM435 scale were studied by testing and analyzing the thickness and phase structure of oxide scale under different rolling conditions.The results show that with the increase of finishing temperature or spinning temperature,the oxide scale thickness of SCM435 wire increases,and a thicker oxide scale(about 20 micr on)will be formed in a short time between 800 ℃ and 900 ℃.Because of the oxidation selectivity of Cr,the iron oxide scale has a high FeO ratio when the finishing temperature is above 870 ℃and the spinning temperature is above 810 ℃.However,when the spinning temperature is higher than 860 ℃,the change of phase structure tends to slow down, and the ratio of FeO does not change much.
引文
[1]吴光亮,孟征兵,李一为,等.薄板坯连铸连轧过程中氧化铁皮变化规律[J].钢铁,2011,46(6):79-85.
    [2]串田仁,武田実佳子.Analysis of Surface Defect Generation Behavior and Decrease of Wire Rolling Defects[J].R&D神戶製鋼技報,2011,61(1):29-33.
    [3]惠亚军,李文远,赵爱民,等.热轧带钢氧化铁皮的微观形貌和氧化动力学研究[J].钢铁研究学报,2013,25(4):54-58.
    [4]李志峰,曹光明,王福祥,等.热轧钢材表面氧化铁皮微观结构表征技术综述[J].轧钢,2017,34(3):56-60.
    [5]肖新星,刘俊亮.热轧板氧化铁皮结构显微分析[J].冶金分析,2010,30(4):36.40.
    [6]张孟仪.普碳钢热轧板表面氧化皮显微结构分析[D].上海:上海大学硕士论文,2007.
    [7]王皓,孙彬,王建明,等.Fe-1Cr钢的高温氧化动力学研究[J].热加工工艺,2016,45(18):46-48.
    [8]宋璐璐.热轧碳钢氧化皮结构、耐蚀性与酸洗行为研究[D].上海:上海交通大学,2009.
    [9]Tominaga J,Wakimoto K and Mori T,et al.Manufacture of Wire Rods with Good Descaling Property[J].Transactions of the Iron and Steel Institute of Japan,1982,22(8):646-656.
    [10]郭大勇,任玉辉,王秉喜,等.精轧和吐丝温度对焊丝钢盘条表面红锈影响研究[J].金属制品,2013,39(2):34-36.

© 2004-2018 中国地质图书馆版权所有 京ICP备05064691号 京公网安备11010802017129号

地址:北京市海淀区学院路29号 邮编:100083

电话:办公室:(+86 10)66554848;文献借阅、咨询服务、科技查新:66554700