摘要
为改善普通涤纶长丝保暖、蓬松等性能,获得异形化、功能性的中空涤纶长丝,分别利用单因子试验和正交试验研究了碱液质量浓度、处理浴温度和保温时间对C型截面中空涤纶长丝减重率和力学性能的影响。得出C型截面中空涤纶长丝的最佳碱减量加工工艺方案:处理浴碱液质量浓度为15.5 g/L,处理浴温度为100℃,保温时间为25 min。通过实际试验对最佳碱减量加工工艺方案进行验证,结果表明,处理后得到的C型截面中空涤纶长丝的减重率达到40.07%,并且其中空形态清晰、C型截面良好且断裂强力损失率下降为42.10%(<45.00%),满足设计要求。
In order to improve the warmth retention and fluffy properties of ordinary polyester filament, the special-shaped and functional hollow polyester filament was fabricated. The effects of alkali liquor concentration, bath temperature and holding time on the weight loss and mechanical properties of hollow polyester filament with C-type section were studied respectively by single factor tests and orthogonal tests. The results show that the optimum process parameters for the fabrication of C-type hollow polyester filament are 15.5 g/L of the mass concentration of alkali solution, 100 ℃ of the bath temperature and 25 min of the holding time. Then the optimum process parameters were verified by experiments,and the results show that the weight loss rate of C-type hollow polyester filament reaches 40. 07% after treatment. Besides,the polyester filament has clear hollow structure and good C-type section,and its breaking strength decreases by 42. 10%( < 45. 00%),which could meet the design requirements.
引文
[1] 赵博.中空涤纶纤维的性能测试及针织产品的开发应用[J].上海毛麻科技,2011(1):12-15.
[2] 包征宇.国内涤纶絮棉及仿羽绒纤维的现状和发展方向[J].合成纤维,1988,2(13):62-65.
[3] 沈惠宾.高速纺中空长丝的工艺设计和结构性能研究[D].苏州:苏州大学,2005.
[4] 王晓.改性中空涤纶纤维性能和针织物研究[D].上海:东华大学,2011.
[5] 佚名.东丽公司研发出新型中空涤纶面料[J].上海纺织科技,2014,42(1):63-64.
[6] 陈金灿.东丽公司研发出新型中空涤纶面料[J].纺织服装周刊,2014(3):97.
[7] 江镇海.日本东丽开发出中空率50%的聚酯长丝[J].合成纤维工业,2014(3):35.
[8] 刘瑞江,张业旺,闻崇炜,等.正交试验设计和分析方法研究[J].实验技术与管理,2010,27(9):52-55.
[9] 杨兰蓉,陈克强.碱减量对超细织物染色性能的影响[J].印染,2001(5):15-19.
[10] 魏贺,蒋金华,陈南梁.经编过程中金属丝耐摩擦性能的研究[J].产业用纺织品,2012,30(4):18-21.
[11] 杜淑芳.超细涤纶柔弹衬布的碱减量工艺[J].染整技术,2002,24(6):43-44.