Zr-4合金与H13模具钢的界面换热行为研究
|
摘要
测定了界面有、无玻璃润滑剂条件下Zr-4合金和H13模具钢的界面接触温度随接触时间的变化曲线,在此基础上分析了界面换热特征,获得了界面换热系数随初始界面温度变化的函数式。结果表明,玻璃润滑剂可有效减缓Zr-4合金与H13钢的界面传热,当Zr-4合金和H13钢的初始界面温度分别为700和470℃时,有玻璃润滑剂时Zr合金表面温度达到稳定的时间约为16.3 s,该时间段内相应的界面换热系数随实验时间的延长由226 W/(m~2·℃)增大到2166W/(m~2·℃),无润滑剂时Zr合金表面温度达到稳定的时间约为7.7 s,该时间段内界面换热系数由250W/(m~2·℃)增大到2700 W/(m~2·℃)。采用本研究确定的换热系数随温度变化的关系式进行热交换模拟可以获得较高的模拟精度,模拟与实验结果的最大误差约为4.5%。
The contact temperature-time curves between Zr-4 alloy and H13 die steel with glass lubrication and without glass lubrication were measured and the characteristics of the interface heat transfer were analyzed. The corresponding empirical formula between the interfacial heat transfer coefficient and the temperatures of both the Zr-4 alloy and die steel were established. The results show that glass lubricant can reduce the interfacial heat transfer between the Zr-4 alloy and the die steel effectively. When the initial temperatures of the Zr-4 alloy and the die steel are 700 and 470 ℃, respectively, the temperature of the zirconium alloy surface tends to be stable at time of about 16.3 s and the IHTC(interfacial heat transfer coefficient) is increased from 226 W/(m~2·℃) to 2166 W/(m~2·℃) during this time under the condition of glass lubrication, while the temperature of the zirconium alloy surface tends to be stable at time of about 7.7 s and the IHTC is increased from 250 W/(m~2·℃) to 2700 W/(m~2·℃) during this time without glass lubrication. The empirical formula of IHTC obtained in this paper has such high accuracy that the maximum error between the simulated and experimental results is about 4.7%.
The contact temperature-time curves between Zr-4 alloy and H13 die steel with glass lubrication and without glass lubrication were measured and the characteristics of the interface heat transfer were analyzed. The corresponding empirical formula between the interfacial heat transfer coefficient and the temperatures of both the Zr-4 alloy and die steel were established. The results show that glass lubricant can reduce the interfacial heat transfer between the Zr-4 alloy and the die steel effectively. When the initial temperatures of the Zr-4 alloy and the die steel are 700 and 470 ℃, respectively, the temperature of the zirconium alloy surface tends to be stable at time of about 16.3 s and the IHTC(interfacial heat transfer coefficient) is increased from 226 W/(m~2·℃) to 2166 W/(m~2·℃) during this time under the condition of glass lubrication, while the temperature of the zirconium alloy surface tends to be stable at time of about 7.7 s and the IHTC is increased from 250 W/(m~2·℃) to 2700 W/(m~2·℃) during this time without glass lubrication. The empirical formula of IHTC obtained in this paper has such high accuracy that the maximum error between the simulated and experimental results is about 4.7%.
引文
[1]Peng Qian(彭倩),Shen Baoluo(沈保罗).Chinese Journal of Rare Materials(稀有金属)[J],2005,29(6):903
[2]Wang Pengfei(王朋飞),Zhao Wenjin(赵文金),Chen Le(陈乐)et al.Rare Metal Materials and Engineering(稀有金属材料与工程)[J],2015,44(5):1150
[3]Wang Ruining(王蕊宁),Xi Zhengping(奚正平),Zhao Yongqing(赵永庆)et al.Rare Metal Materials and Engineering(稀有金属材料与工程)[J],2007,36(5):808
[4]Fan Xuanhua(范宣华),Cai Lixun(蔡力勋),Hu Shao(胡绍)et al.Journal of materials engineering(材料工程)[J],2005(1):37
[5]Wang Xufeng(王旭峰),Li Zhongkui(李中奎),Zhou Jun(周军)et al.Hot Working Technology(热加工工艺)[J],2012,41(2):71
[6]Zhang Libo(张立波),Quan Xiaohui(权晓惠),Jing Yunhai(荆云海)et al.Heavy Machinery(重型机械)[J],2015(6):11
[7]Wang Lixia(王丽霞),Zhang Xiyan(张喜燕),Xue Xiangyi(薛祥义)et al.Rare Metal Materials and Engineering(稀有金属材料与工程)[J],2013,42(1):153
[8]Jing Yunhai(荆云海),Zhang Mingxiang(张明祥),Wang Wei(王伟)et al.Heavy Machinery(重型机械)[J],2015(2):35
[9]Rosochowska M,Balendra R,Chodnikiewicz K.Journal of Materials Processing Technology[J],2003,135(2-3):204
[10]Zhou Huidong(周汇东).Water-cooled Power Reactor Fuel Cladding Material:Zirconium Alloy(水冷动力堆燃料包壳材料:锆合金)[M].Beijing:Atomic Energy Press,1979
[11]Yang Shiming(杨世铭),Tao Wenquan(陶文铨).Heat Transfer(传热学)[M].Beijing:Higher Education Press,2006
[2]Wang Pengfei(王朋飞),Zhao Wenjin(赵文金),Chen Le(陈乐)et al.Rare Metal Materials and Engineering(稀有金属材料与工程)[J],2015,44(5):1150
[3]Wang Ruining(王蕊宁),Xi Zhengping(奚正平),Zhao Yongqing(赵永庆)et al.Rare Metal Materials and Engineering(稀有金属材料与工程)[J],2007,36(5):808
[4]Fan Xuanhua(范宣华),Cai Lixun(蔡力勋),Hu Shao(胡绍)et al.Journal of materials engineering(材料工程)[J],2005(1):37
[5]Wang Xufeng(王旭峰),Li Zhongkui(李中奎),Zhou Jun(周军)et al.Hot Working Technology(热加工工艺)[J],2012,41(2):71
[6]Zhang Libo(张立波),Quan Xiaohui(权晓惠),Jing Yunhai(荆云海)et al.Heavy Machinery(重型机械)[J],2015(6):11
[7]Wang Lixia(王丽霞),Zhang Xiyan(张喜燕),Xue Xiangyi(薛祥义)et al.Rare Metal Materials and Engineering(稀有金属材料与工程)[J],2013,42(1):153
[8]Jing Yunhai(荆云海),Zhang Mingxiang(张明祥),Wang Wei(王伟)et al.Heavy Machinery(重型机械)[J],2015(2):35
[9]Rosochowska M,Balendra R,Chodnikiewicz K.Journal of Materials Processing Technology[J],2003,135(2-3):204
[10]Zhou Huidong(周汇东).Water-cooled Power Reactor Fuel Cladding Material:Zirconium Alloy(水冷动力堆燃料包壳材料:锆合金)[M].Beijing:Atomic Energy Press,1979
[11]Yang Shiming(杨世铭),Tao Wenquan(陶文铨).Heat Transfer(传热学)[M].Beijing:Higher Education Press,2006