工艺参数对激光-电弧复合焊缝成形及拉伸性能的影响
|
摘要
以8 mm厚的304不锈钢为试验材料,采用高功率碟片激光与熔化极电弧复合焊接的方法,开展了全熔透焊接工艺试验研究,分析了送丝速度、激光功率、焊接速度、光丝间距等工艺参数对焊缝成形及焊接接头拉伸性能(抗拉强度、延伸率)的影响。结果表明,增大送丝速度能够减少底部驼峰及咬边现象的产生,改善焊缝成形,在一定范围内能够提高焊缝抗拉强度和延伸率;但当送丝速度超过一定值时,再继续增大送丝速度会导致抗拉强度降低;提高激光功率或减小焊接速度可减少驼峰和消除咬边现象,但会降低接头抗拉强度和延伸率。当光丝间距在1 mm时,焊缝成形较好,焊接接头的抗拉强度及延伸率较好,获得的无咬边和驼峰缺陷的焊接接头抗拉强度可达695 MPa,达到母材的97.89%,延伸率为41.5%,达到母材的76.85%。
Full penetration welding process experiments had been carried out on 8 mm 304 stainless steel by hybrid laser-arc welding using high power disk laser and MIG arc. The effects on the weld formation and tensile property(tensile strength, elongation) of wire feeding speed, laser power, welding speed, distance between laser and arc were studied. The results show that it can decrease back hump and eliminate undercut leading weld formation improvement with increasing wire feeding speed. And it can improve tensile strength and elongation, but if the wire feeding speed is too big, the tensile strength would decrease. It can decrease back hump and eliminate undercut by enhancing laser power but the tensile strength and elongation would decrease. When the distance between laser and arc is 1 mm, it can obtain a good weld formation and the tensile strength and elongation are better. The tensile strength and elongation can be up to 695 MPa and 41.5%, which reach 97.89% and 76.85% of the base material, respectively.
Full penetration welding process experiments had been carried out on 8 mm 304 stainless steel by hybrid laser-arc welding using high power disk laser and MIG arc. The effects on the weld formation and tensile property(tensile strength, elongation) of wire feeding speed, laser power, welding speed, distance between laser and arc were studied. The results show that it can decrease back hump and eliminate undercut leading weld formation improvement with increasing wire feeding speed. And it can improve tensile strength and elongation, but if the wire feeding speed is too big, the tensile strength would decrease. It can decrease back hump and eliminate undercut by enhancing laser power but the tensile strength and elongation would decrease. When the distance between laser and arc is 1 mm, it can obtain a good weld formation and the tensile strength and elongation are better. The tensile strength and elongation can be up to 695 MPa and 41.5%, which reach 97.89% and 76.85% of the base material, respectively.
引文
1 Xiao Rongshi,Wu Shikai.Chinese Journal of Lasers,2008,35(11),1680 (in Chinese).肖荣诗,吴世凯.中国激光,2008,35(11),1680.
2 Wang Xiaonan,Chen Changjun,Zhu Guangjiang,et al.Laser & Optoelectronics Progress,2014,51(3),030008 (in Chinese).王晓南,陈长军,朱广江,等.激光与光电子学进展,2014,51(3),030008.
3 Gao Zhiguo,Huang Jian,Li Yaling,et al.Transactions of the China Welding Institution,2008,29 (12),69 (in Chinese).高志国,黄坚,李亚玲,等.焊接学报,2008,29(12),69.
4 Zhao Lin,Tsukamoto Susumu,Arakane Goro,et al.Chinese Journal of Lasers,2015,42(4),0406006 (in Chinese).赵琳,塚本进,荒金吾郎,等.中国激光,2015,42(4),0406006.
5 Cui Li,He Dingyong,Li Xiaoyan,et al.Chinese Journal of Lasers,2011,38(1),0103002 (in Chinese).崔丽,贺定勇,李晓延,等.中国激光,2011,38(1),0103002.
6 Chen Yanbin,Feng Jiecai,Li Liqun.Journal of Mechanical Enginee-ring,2016,52(6),47 (in Chinese).陈彦宾,冯杰才,李俐群.机械工程学报,2016,52(6),47.
7 Shi Pengfei,Huang Jian,Tantai Fanliang,et al.Chinese Journal of Lasers,2017,44(10),1002001 (in Chinese).史鹏飞,黄坚,姚成武,等.中国激光,2017,44(10),1002001.
8 Cai Xiaoyu,Li Huan,Yang Lijun,et al.Chinese Journal of Lasers,2014,41(5),0503001 (in Chinese).蔡笑宇,李桓,杨立军,等.中国激光,2014,41(5),0503001.
9 Wahba M,Mizutani M,Katayama S.Materials and Design,2016,97,1.
10 Steen Erik Nielsen.Physics Procedia,2015,78,24.
2 Wang Xiaonan,Chen Changjun,Zhu Guangjiang,et al.Laser & Optoelectronics Progress,2014,51(3),030008 (in Chinese).王晓南,陈长军,朱广江,等.激光与光电子学进展,2014,51(3),030008.
3 Gao Zhiguo,Huang Jian,Li Yaling,et al.Transactions of the China Welding Institution,2008,29 (12),69 (in Chinese).高志国,黄坚,李亚玲,等.焊接学报,2008,29(12),69.
4 Zhao Lin,Tsukamoto Susumu,Arakane Goro,et al.Chinese Journal of Lasers,2015,42(4),0406006 (in Chinese).赵琳,塚本进,荒金吾郎,等.中国激光,2015,42(4),0406006.
5 Cui Li,He Dingyong,Li Xiaoyan,et al.Chinese Journal of Lasers,2011,38(1),0103002 (in Chinese).崔丽,贺定勇,李晓延,等.中国激光,2011,38(1),0103002.
6 Chen Yanbin,Feng Jiecai,Li Liqun.Journal of Mechanical Enginee-ring,2016,52(6),47 (in Chinese).陈彦宾,冯杰才,李俐群.机械工程学报,2016,52(6),47.
7 Shi Pengfei,Huang Jian,Tantai Fanliang,et al.Chinese Journal of Lasers,2017,44(10),1002001 (in Chinese).史鹏飞,黄坚,姚成武,等.中国激光,2017,44(10),1002001.
8 Cai Xiaoyu,Li Huan,Yang Lijun,et al.Chinese Journal of Lasers,2014,41(5),0503001 (in Chinese).蔡笑宇,李桓,杨立军,等.中国激光,2014,41(5),0503001.
9 Wahba M,Mizutani M,Katayama S.Materials and Design,2016,97,1.
10 Steen Erik Nielsen.Physics Procedia,2015,78,24.