哈兹列特连铸连轧铝合金板带组织和性能研究
|
摘要
哈兹列特连铸连轧工艺是一种短流程的铝合金板带坯料生产新工艺,它通过将熔融金属液馈入哈兹列特连续铸造机得到约19mm厚连续铸坯,然后直接多机架连轧至2mm左右。相对于传统的铸锭热轧工艺省去了铸造合金大板锭,锯头铣面,均匀化退火,大加工量的热粗轧等多道工序,具有短流程,节能降耗,降低生产成本等工艺优势。伊川电力集团国内首次引进该工艺,为充分了解哈兹列特连续铸造工艺特点及其连铸连轧产品显微组织和性能,本文选取了3004,3003,5052等铝合金,采用金相显微镜(OM)、X射线衍射(XRD)、扫描电镜(SEM)及能谱分析(EDS)等分析手段,通过拉伸试验、弯曲试验、腐蚀试验等性能测试,研究了哈兹列特连铸连轧、直冷铸锭热轧及双辊式铸轧三种不同铝合金板带供坯生产方式其产品显微组织和性能。论文主要工作及研究结果如下：
(1)结合哈兹列特连续铸造工艺特点研究分析了哈兹列特3004铝合金连续铸坯显微组织形成特点和表面形貌。
(2)对哈兹列特3004铝合金连轧板坯进行高温长时间的退火,研究了连铸连轧3004铝合金回复再结晶。结果发现在510℃保温10h,可改善第二相形态、含量,均匀化合金成分,获得完全再结晶组织,改善后续冷轧加工性能。
(3)以登封铝业公司铸轧3003铝合金冷轧产品为对比,研究了哈兹列特连铸连轧3003铝合金显微组织及拉伸、弯曲力学性能,探讨了哈兹列特连铸连轧3003铝合金替代铸轧法从而省去冷轧生产幕墙铝单板的可行性。结果发现哈兹列特连铸连轧产品(抗拉强度234.47MPa,伸长率8.02%)具有与铸轧产品(抗拉强度239.94MPa,伸长率5.45%)相当的抗拉强度,好的塑性加工性能,且达到行业标准YS／T 429.1—2000《幕墙板板基》规定的力学性能指标：抗拉强度110-177MPa,铝板延伸率≥5%。完全可以替代铸轧生产工艺,从而可以省去后续冷轧,达到缩短生产周期,降低生产成本的目的。
(4)以鑫泰铝业公司热轧5052冷轧成品板为对比,研究了哈兹列特连铸连轧5052冷轧成品板显微组织和拉伸力学性能及腐蚀性能。结果发现哈兹列特连铸连轧产品(抗拉强度216.2MPa,伸长率14.26%)具有比热轧产品(抗拉强度199.75MPa,伸长率23.78%)高的强度,同时塑性加工性能良好。达到GB/T3880.2—2006《一般工业用铝及铝合金板、带材第二部分：力学性能》规定的5052H32态厚度0.5-1.5mm抗拉强度不小于210-260MPa,延伸率不小于6%的使用标准。而腐蚀性能测试结果表明哈兹列特连铸连轧和热轧5052冷轧成品板腐蚀电流密度相差不大,具有相似的抗腐蚀能力。
Hazelett continuous casting and rolling process is a new technology of the aluminum alloy plate production with short process characteristics, it is feed by molten liquid metal into the Hazelett continuous casting machine to be about 19mm thick continuous slab, and then directly continuous rolled to be about 2mm thick. Compared with traditional direct casting and hot rolling process(DC process), it eliminated casting large panel ingots, sawing head, milling surface, homogenization annealing, large amount of thermal processing of rough rolling and other multi-channel processes, With advantages of short process, energy saving, lower production cost. Yichuan Power Group is the first company introduced the technology in China, in order to fully understand the Hazelett continuous casting and rolling process and microstructures and properties of its products, This paper selected 3004,3003,5052 aluminum alloy, using optical microscopy (OM), X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive analysis (EDS) and other analytical tools, Through the tensile, bending, corrosion resistance and other performance testing, Studied microstructures and mechanical properties of Hazelett, DC process and twin-roll casting three different modes'products,research works and findings are as follows:
(1) Studied microstructure characteristics and surface morphology of Hazelett continuous casting 3004 aluminum alloy.
(2) Studied recovery and recrystallization of Hazelett continuous casted and rolled 3004 aluminum alloy. The results found that in 510℃insulation 10h can improve the second phase shape, content, uniformity of alloy composition, to obtain complete recrystallized structure, to improve the follow-up cold-rolling process performance.
(3) In comparison with twin-roll casting and cold rolled 3003 aluminum alloy from Dengfeng, Studied the microstructure and mechanical properties of the Hazelett products, Researched the feasibility of Hazelett take the place of twin-roll casting to produce curtain wall plate, The results showed that Hazelett products (tensile strength 234.47MPa, elongation rate of 8.02%) have a similar tensile strength, better plastic processing performance than twin-roll casting and cold rolled products(tensile strength 239.94MPa, elongation rate of 5.45%), meet industry standards YS/T 429.1-2000 provisions of the mechanical properties:Tensile strength:110-177MPa, aluminum elongation:≥5%. So Hazelett can replace twin-roll casting process, eliminating the need of cold rolling and shorten the production cycle in order to reduce production costs.
(4) In comparison with DC process and cold rolled 5052 aluminum alloy from Xintai,studied the microstructure and properties of the Hazelett products, the results showed that Hazelett products (tensile strength 216.2MPa, elongation rate of 14.26%) have higher strength and good plastic processing more than DC products (tensile strength 199.75MPa, elongation rate of 23.78%).Achieve GB/T3880.2-2006 "Wrought aluminum and aluminum alloy plates, sheets and strips for general engineering—Part 2:Mechanical properties" provisions:5052H32 of 0.5-1.5mm thickness tensile strength not less than 210-260MPa, elongation does not less than 6%.The corrosion test results shown that Hazelett and DC product have the similar corrosion resistance.
(1)结合哈兹列特连续铸造工艺特点研究分析了哈兹列特3004铝合金连续铸坯显微组织形成特点和表面形貌。
(2)对哈兹列特3004铝合金连轧板坯进行高温长时间的退火,研究了连铸连轧3004铝合金回复再结晶。结果发现在510℃保温10h,可改善第二相形态、含量,均匀化合金成分,获得完全再结晶组织,改善后续冷轧加工性能。
(3)以登封铝业公司铸轧3003铝合金冷轧产品为对比,研究了哈兹列特连铸连轧3003铝合金显微组织及拉伸、弯曲力学性能,探讨了哈兹列特连铸连轧3003铝合金替代铸轧法从而省去冷轧生产幕墙铝单板的可行性。结果发现哈兹列特连铸连轧产品(抗拉强度234.47MPa,伸长率8.02%)具有与铸轧产品(抗拉强度239.94MPa,伸长率5.45%)相当的抗拉强度,好的塑性加工性能,且达到行业标准YS／T 429.1—2000《幕墙板板基》规定的力学性能指标：抗拉强度110-177MPa,铝板延伸率≥5%。完全可以替代铸轧生产工艺,从而可以省去后续冷轧,达到缩短生产周期,降低生产成本的目的。
(4)以鑫泰铝业公司热轧5052冷轧成品板为对比,研究了哈兹列特连铸连轧5052冷轧成品板显微组织和拉伸力学性能及腐蚀性能。结果发现哈兹列特连铸连轧产品(抗拉强度216.2MPa,伸长率14.26%)具有比热轧产品(抗拉强度199.75MPa,伸长率23.78%)高的强度,同时塑性加工性能良好。达到GB/T3880.2—2006《一般工业用铝及铝合金板、带材第二部分：力学性能》规定的5052H32态厚度0.5-1.5mm抗拉强度不小于210-260MPa,延伸率不小于6%的使用标准。而腐蚀性能测试结果表明哈兹列特连铸连轧和热轧5052冷轧成品板腐蚀电流密度相差不大,具有相似的抗腐蚀能力。
Hazelett continuous casting and rolling process is a new technology of the aluminum alloy plate production with short process characteristics, it is feed by molten liquid metal into the Hazelett continuous casting machine to be about 19mm thick continuous slab, and then directly continuous rolled to be about 2mm thick. Compared with traditional direct casting and hot rolling process(DC process), it eliminated casting large panel ingots, sawing head, milling surface, homogenization annealing, large amount of thermal processing of rough rolling and other multi-channel processes, With advantages of short process, energy saving, lower production cost. Yichuan Power Group is the first company introduced the technology in China, in order to fully understand the Hazelett continuous casting and rolling process and microstructures and properties of its products, This paper selected 3004,3003,5052 aluminum alloy, using optical microscopy (OM), X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive analysis (EDS) and other analytical tools, Through the tensile, bending, corrosion resistance and other performance testing, Studied microstructures and mechanical properties of Hazelett, DC process and twin-roll casting three different modes'products,research works and findings are as follows:
(1) Studied microstructure characteristics and surface morphology of Hazelett continuous casting 3004 aluminum alloy.
(2) Studied recovery and recrystallization of Hazelett continuous casted and rolled 3004 aluminum alloy. The results found that in 510℃insulation 10h can improve the second phase shape, content, uniformity of alloy composition, to obtain complete recrystallized structure, to improve the follow-up cold-rolling process performance.
(3) In comparison with twin-roll casting and cold rolled 3003 aluminum alloy from Dengfeng, Studied the microstructure and mechanical properties of the Hazelett products, Researched the feasibility of Hazelett take the place of twin-roll casting to produce curtain wall plate, The results showed that Hazelett products (tensile strength 234.47MPa, elongation rate of 8.02%) have a similar tensile strength, better plastic processing performance than twin-roll casting and cold rolled products(tensile strength 239.94MPa, elongation rate of 5.45%), meet industry standards YS/T 429.1-2000 provisions of the mechanical properties:Tensile strength:110-177MPa, aluminum elongation:≥5%. So Hazelett can replace twin-roll casting process, eliminating the need of cold rolling and shorten the production cycle in order to reduce production costs.
(4) In comparison with DC process and cold rolled 5052 aluminum alloy from Xintai,studied the microstructure and properties of the Hazelett products, the results showed that Hazelett products (tensile strength 216.2MPa, elongation rate of 14.26%) have higher strength and good plastic processing more than DC products (tensile strength 199.75MPa, elongation rate of 23.78%).Achieve GB/T3880.2-2006 "Wrought aluminum and aluminum alloy plates, sheets and strips for general engineering—Part 2:Mechanical properties" provisions:5052H32 of 0.5-1.5mm thickness tensile strength not less than 210-260MPa, elongation does not less than 6%.The corrosion test results shown that Hazelett and DC product have the similar corrosion resistance.
引文
[1]刘静安,尹晓辉.我国铝轧制工业的发展现状及与国际先进水平的差距(续)[J].有色金属加工,2008,37(2)：1-3
[2]http://www.investgz.gov.cn/zsproject/Readproject.asp?ID=3022.10万吨／年高精度铝板带及铝合金复合材料工程项目建议书
[3]http://www.cnitdc.com/juke/juke_bjfx.htm.巨科铝业进军铝加工业的背景分析
[4]肖亚庆主编.铝加工技术实用手册[M].北京：冶金工业出版社,2005
[5]钱宝华.加工工艺对5052合金板材组织与性能的影响[D].重庆：重庆大学,2008
[6]王祝堂,任柏峰,周涛.中国铝板带箔加工设备现状及发展方向[J].上海有色金属,2004,25(3)：128-132
[7]程磊,谢水生,黄国杰.中国铝板带箔轧制工业的发展[J].轻合金加工技术,2007,35(11)：12-17
[8]傅振有.铝及铝合金连续铸轧工艺及铸轧机列的设备组成[J].轻合金加工技术,1985,4：1-4
[9]潘世民.世界铝连续铸轧技术综述[J].世界有色金属,2003,3：49-51
[10]王祝堂.迈向新世纪的世界铝带坯铸轧[J].轻合金加工技术,2001,29(4)：8-10
[11]王祝堂.铝带坯双辊式连续铸轧技术的现状与新进展[J].世界有色金属,1997,7：18-21
[12]Kaiser Aluminum&Chemical Corporation. A method for making beverage can sheet [P]. World Intellectual Property Organization:Wo97/11205,1997-03-27
[13]范靖亚.戈尔登铝公司开发的连续铸轧高质量铝薄板[J].轻合金加工技术,1997,25(4)：27-29
[14]马道章.哈兹列特工艺在铝板带连铸连轧应用中若干问题的探讨[J].铝加工,2005,162：18-24
[15]Peter Regan, Wojtek Szczypiorski. 哈兹列特工艺及其在中国的前景.2005
[16]刘小玲,马道章.浅谈哈兹列特连铸技术在我国铝板带生产上的应用[J].上海有色金属,2004,25(2)：77-82
[17]大卫.哈兹列特.采用哈兹列特工艺把电解铝液加工成铝板带.
[18]Hazelett Strip-casting Corporation. Non-rotating, levitating, cylindrical air-pillow apparatus and method for supporting and guiding an endless flexible casiting belt into the entrance of a continuous metal-casting machine [P]. World Intellectual Property Organization:Wo 01/08835A1,2001-08-02
[19]John M.A.Dompas. Belt back-up apparatus and coolant application means for twin-belt casting machines[P]. United States Patent:3937274,1976-2-10
[20]Hazelett Strip-casting Corpration. Magnetized finned backup rollers for guiding and stabilizing an endless casting belt[P]. Canadian Intellectual Property Office:CA 2259604,2005-06-07
[21]Alcan international limited. Surface texturing of casting belts of continuous casting machines[P]. World Intellectual Property Organization:WO2005/032743A1,2005-4-14
[22]Dr.Subodh, K.Das. Evaluation and characterization of in-line annealed continuous cast aluminum sheet. Final technical report, August2005
[23]James G.Morris, Chi-Sing Man, and Tongguang Zhai. prediction of texture and formability of continuous cast AA5000 and 2000 Series aluminum alloy sheets and their quality improvement.
[24]W.C.Liu, T.Zhai, J.G.Morris. Texture evolution of continuous cast and direct chill cast AA3003 aluminum alloys during cold rolling[J]. Scripta Materialia,2004,51:83-88
[25]W.C.Liu, Z.Li, C.S.Man. Effect of heating rate on the microstructure and tecture of continuous cast AA3105 aluminum alloy[J]. Materials Science and Engineering A,2008, 478:173-180
[26]W.C.Liu, J.G.Morris. Effect of hot and cold deformation on the P{011}<455> recrystallization tecture in a continuous cast Al-Mn-Mg aluminum alloy[J]. Scripta Materialia,2006,54:2095-2099
[27]Jiantao Liu, James G.Morris. Macro-, micro- and mesotecture evolutions of continuous cast and direct chill cast AA3105 aluminum alloy during cold rolling[J]. Materials and Engineering A,2003,357:277-296
[28]W.C.Liu, Z.Li, C.S.Man, D.Raabe, J.G.Morris. Effect of precipitation on rolling tecture evolution in continuous cast AA3105 aluminum alloy[J]. Materials Science and Engineering A,2006,434:105-113
[29]W.C.Liu, C.S.Man, D.Raabe, J.G.Morris. Effect of hot and cold deformation on the recrystallization tecture of continuous csat AA5052 aluminum alloy[J]. Scripta Materialia,2005,53:1273-1277
[30]Jiantao Liu, James G.Morris. Recrystallization microstructures and tectures in AA5052 continuous cast and direct chill cast aluminum alloy[J]. Materials Science and Engineering A,2004,385:342-351
[31]X.Y.Wen, Z.D.Long, W.M.Yin, T.Zhai, Z.Li, S.K.Das. Texture evolution in continuous casting aluminum alloy AA5052 hot band during biacial stretching[J]. Materials Science and Engineering A,2007,454-455:245-251
[32]Y.M.Zhao, W.Wen, J.G.Morris. The differences in particle structures and recrystallization behaviors beteeen DC and CC AA5052 aluminum alloys[J]. Materials Science and Engineering A,2004,373:167-174
[33]W.C.Liu, B.Radhakrishnan, Z.Li, J.G.Morris. Through-thickness tecture gradient in continuous cast AA5052 aluminum alloy sheet[J]. Materials Science and Engineering A, 2008,472:170-178
[34]W.C.Liu, J.G.Morris. Effect of hot and cold deformation on thepfiber rolling tecture in continuous cast AA5052 alumium alloy[J]. Scripta Materialia,2005,52:1317-1321
[35]X.F.Yu, Y.M.Zhao, X.Y.Wen, T.Zhai. A study of mechanical isotropy of continuous cast and direct chill cast AA5182 Al alloys[J]. Materials Science and Engineering A394(2005)376-384
[36]W.C.Liu, T.Zhai, J.G.Morris. Comparison of recrystallization and recrystallization tectures in cold rolled DC and CC AA5182 aluminum alloys[J]. Materials Science and Engineering A,2003,358:84-93
[37]W.C.Liu, J.G.Morris. Effect of initial tecture on the recrystallization tecture of cold rolled AA5182 aluminum alloy[J]. Materials Science and Engineering A,2005,402: 215-227
[38]W.C.Liu, J.G.Morris. Effect of pre-treantment on recrystallization and recry stallization tectures of cold rolled CC AA5182 aluminum alloy[J]. Materials Science and Engineering A,2003,363:253-262
[39]W.C.Liu, J.Li, H.Yuan and Q.X.Yang.Effect of recobery on the recrystallization tecture of an Al-Mg alloy[J]. Scripta Materialia,2007,57:833-836
[40]W.C.Liu, T.Zhai, C.S.Man, J.G.Morris. Quantification of recrystallization tecture evolution in cold rolled AA5182 aluminum alloy[J]. Scripta Materialia,2003,49: 539-545
[41]W.C.Liu, J.G.Morris. Comparison of the tecture evolution in cold rolled DC and SC AA5182 aluminum alloys [J]. Materials Science and Engineering A,2003,339:183-193
[42]J.Li, W.C.Liu, T.Zhai, E.A.Kenik. Comparison of recrystallization tecture in cold-rolled continuous cast AA5083 and 5182 aluminum alloys[J]. Scripta Materialia,2005,52: 163-168
[43]W.C.Liu, J.G.Morris. Kinetics of the formation of the β fiber folling tecture in continuous cast AA 5xxx series aluminum alloys[J].2002,47:743-748
[44]Xiang-Ming Cheng, James G.Morris. Tecture, microstructure and formability of SC and DC cast Al-Mg alloys[J]. Materials Science and Engineering A,2002,323:32-41
[45]马道章.生产蒙皮用铝合金板材的先进工艺[J].上海有色金属,2001,22(2)：80-82
[46]马道章.连铸连轧—降低汽车用铝材高成本的好工艺[J].轻合金加工技术,2006,34(6)：6-7
[47]关绍康.高性能铝合金车身板的产业化及发展趋势.河南省铝加工业发展研讨会专家报告篇.2004年9月
[48]Zhong Li, Steven Kirkland. Development of continuous cast 5754 alloy sheet for automotive application [J]. TMS,2005
[49]H.N.Azari, S.X.Girard, D.S.Wilkinson, and D.J.Lloyd. Effect of thermonechanical treatment on the evolution of rolling and recrystallization tectures in twin-belt cast AA5754 aluminum alloy[J]. Metallurgical and Materials Transactions A, Vol35A,2004: 1839-1851
[50]Alcan International Limited. Belt casting of non-ferrous and light metals and apparatus therefore [P]. World Intellectual Property Organization:Wo2005/032744,2005-04-14
[51]Nippon Light Metal Company, Ltd. Speed synchronization system of aluminum alloy slab continuous casting and rolling line and production facility and method of production of aluminum alloy contiuously cast and rolled slab using same[P]. World Intellectual Property Organization:Wo 2007/066448A1,2007-6-14
[52]Nippon Light Metal Co, Ltd. Aluminum alloy sheet method for manufacturing the same[P]. Word Intellectual Property Organization:Wo2006/011242,2006-2-2
[53]王祝堂.全球首条汽车铝板带连铸轧生产线投产[J].轻合金加工技术,2005,33(3)
[54]Nippon Light Metal Company Ltd. Method for producing Al-Mg-Si based aluminum alloy plate excellent in bake-hardenability[P]. European patent application: EP1715067A1,2006-10-25
[55]Nippon Light Metal Company Ltd. Method for producing Al-Mg-Si alloy excellent in bake-hardenability and hemmability[P]. European patent application:EP1702995A1, 2006-09-20
[56]王自涛.铝材应用发展机遇与挑战.第五届中国河南投资贸易洽谈会铝产业发展研讨会专业报告.2008年8月
[57]陈永禄,傅高升等.经高效熔体处理的易拉罐用铝带材的中间退火工艺探讨[J].有色金属加工,2003,32(1)：12-15
[58]彭开萍,陈文哲等.3004铝合金拉伸变形特征[J].机械工程材料,2005,29(12)：13-16
[59]彭开萍等.易拉罐用铝材锯齿屈服现象的研究[J].中国有色金属学报,2005,15(5)：694-699
[60]彭开萍等.3004铝合金动态应变时效的微观机理[J].材料热处理学报,2005,26(6)：57-61
[61]陈鸿铃等.高成形性罐用铝材热变形过程的微观组织观察[J].福建工程学院学报,2005,3(1)：61-65
[62]胡卓超张德芬黄涛等.3104铝合金的流变应力行为与动态再结晶[J].机械工程材料,2005,29(2)：6-9
[63]张德芬等.3104铝合金固溶及时效处理后的冷轧织构[J].材料热处理学报,2005,26(5)：88-91
[64]张德芬等.3104铝合金冷轧变形织构的分析.轻合金加工技术[J],2003,31(7)：22-25
[65]张德芬,黄涛等.3104铝合金再结晶织构的研究.材料工程[J],2004,11：28-31
[66]胡卓超等.电场退火对3104铝合金板显微组织与再结晶织构的影响[J].中国有色金属学报,2004,14(8)：1366-1371
[67]张德芬等.热轧3104铝合金的显微组织[J].有色金属,2004,56(4)：14-18
[68]张德芬,左良.预回复退火对3104铝合金再结晶织构和显微组织的影响[J].石油化工高等学校学报,2004,17(3)：62-65
[69]胡卓超,张德芬等.形变模式对3104铝合金板微取向流变行为的影响[J].材料科学与工艺,2005,13(1)：12-15
[70]黄光杰,汪凌云.3104铝合金板材织构和制耳行为研究[J].重庆大学学报,2000,23(3)：20-23
[71]黄光杰.3104铝合金高温塑性变形本构关系研究[J].材料导报,2006,20(7)：460-462
[72]黄光杰.3104铝合金流变应力行为[J].重庆大学学报.2007,30(1)：70-72
[73]沈健,张新明.3004铝合金的再结晶和织构[J].中南矿冶学院学报,1994,25(6)：
[74]沈健,张新明.中间退火对3004合金组织织构和各向异性的影响[J].1994,17(3)：44-47
[75]张明,温熙宇.3004铝合金铸轧板均匀化后冷轧的组织与织构[J].中国有色金属学报,1995,5(4)：151-153
[76]温熙宇,王玉林.3004铝合金铸轧板均匀化热处理的组织和织构[J].金属热处理学报,1994,15(3)：44-48
[77]温熙宇,王玉林等.罐材用3004铝合金铸轧板经中间退火和冷轧后所得冷轧板的ODF分析[J].轻金属,1994,3：43-45
[78]朱清洋.3104铝合金化学成分优化及织构研究[D].重庆：重庆大学,2006
[79]肖亚庆主编,铝加工技术实用手册[M].北京：冶金工业出版社,2005
[80]刘静安,盛春磊,朱英.铝材在包装、容器工业上的开发与应用[J].四川有色金属,2006.6第2期：1-8
[81]胡汉起编.金属凝固原理[M].北京：机械工业出版社,2000.11,第2版
[82]佟长清.3004合金铸锭锰偏析及均匀化处理[J].轻合金加工技术,1997,25(1)：31-36
[83]孙东立,姜东峰.均匀化处理对3004铝合金显微组织的影响[J].中国有色金属学报,1999,9(3)：556-558
[84]D.T.L. Alexander, A.L.Greer. Formation of eutectic intermetallic rosettes by entrapment of liquid droplets during cellular columnar growth[J]. Acta Materialia 52 (2004) 5853-5861
[85]Y.J.Li, L.Arnberg. Evolution of eutectic intermetallic particles in DC-cast AA3003 alloy during heating and homogenization[P]. Materials Science and Engineering A347 (2003) 130-135
[86]Novelis Inc. Method of and molten metal feeder for continuous casting[P]. World Intellectual Property Organization:Wo2006/089419A1,2006-8-31
[87]Hazelett Strip-Casting Corporation. Radial-flow distributor for wide uniform nonturbulent non-dribbline pouring of molten metal into a continuous metal-casting machine-methods and apparatus[P]. United States Patent:5804136,1998-9-8
[88]Peyman Ashtari, Kevin Gatenby. Reheating of solid shell during twin belt-casting of an Al-Fe-Si alloy[J]. Scripta Materialia 58 (2008) 150-153
[89]Peyman Ashtari and Kevin Gatenby. Formation of inverse segregation on the surface of belt-cast Al-Fe-Si and Al-Fe-Si-Mn alloys. Scripta Materialia 57 (2007) 627-630
[90]苏鸿英.用哈兹列特铸造工艺生产板材表面条纹的消除[J].有色金属加工,1995,6：20-24
[91]Wojtek Szczypiorki等.哈兹雷特连铸带材涂层的优越性[J].有色金属加工,1995第三期：30-35
[92]Pedro G.Q.NETTO, Roberto P.TAVARES, Mihaiela IS AC. A technique for the evaluation of instantaneous heat fluces for the horizontal strip casting of aluminum alloys[J]. ISIJ International, Vol.41 (2001), No.11:1340-1349
[93]B.Farouk, D.Apelian and Y.G.Kim. A numerical and experimental study of the solidification rate in a twin-belt caster[J]. Metallurgical Transactions B,1992, Volume 23B:477-492
[94]A.G.Gerber, A.C.M.Sousa. A parametric study of the Hazelett thin-slab casting process[J]. Journal of Materials Processing Technology 49 (1995) 41-56
[95]S.Bounds, G.Moran, K.Pericleous, M.Cross, and T.N.Croft. A computational model for defect prediction in shape castings based on the interaction of free surface flow, heat transter, and solidification phenomena[J]. Metallurgical and Materials Transactions B, Volume31B, june 2000:515-527
[96]M. Aghaie-khafri. The effect of homogentization on the recrystallization of an Al-Mn-Mg Alloy sheet[J]. Journal of Materials Science,2005,40:1135-1139
[97]S.Sarkar, M.A.Wells, W.J.Poole. Softening behaviour of cold rolled continuous cast and ingot cast aluminum alloy AA5754[J]. Materials Science and Engineering A 421 (2006) 276-285
[98]Jiantao Liu, Robert E.Dick, Joseph M.Fridy, Thomas N.Rouns. Crystallographic tecture evolution of continuous cast Al-Mn-Mg alloy sheet during cold rolling and annealing[P]. Materials Science and Engineering A458 (2007) 73-87
[99]王祝堂.铝及铝合金热轧时组织的变化[J].轻合金加工技术,2002,30(3)：8
[100]马道章.开辟易拉罐罐体材料生产的新途径[J].上海有色金属,2002,23(2)：70-73
[101]K.Marthinsen, O.Daaland, T.Turu, and E.Nes. The spatial distribution of nucleation sites and its effect on recrystallization kinetics in commercial aluminum alloys [J]. Metallurgical and Materials transactions A,2003, Vol.34:2705-2715
[102]张宝昌主编.有色金属及其热处理[M].西安：西北工业大学出版,1993.10,第1版
[103]J.M.Howe. Metallographi and differential scanning calorimetry analyses of precipitation and recrystallization in an Al-Mn alloy[J]. Metallurgical Transactions A, Vol.17A,1986: 593-605
[104]张忠玉主编.铝及铝合金工艺与设备[M].长沙：中南大学出版社,2006.11,第1版
[105]刘朝义,陈瑶贵.氟碳喷涂单层铝板的加工过程[J].中国建材科技,2003,12(4)：53-55
[106]赵志远.铝和铝合金牌号与金相图谱速用速查及金相检验技术创新应用指导手册[M].北京：中国知识出版社,2005：797-795
[107]荣宝星.HAZELETT双带连铸机和连轧设备[J].上海金属(有色分册),1987,8 (4)：48-55
[108]刘小玲,马道章.浅谈哈兹列特连铸技术在我国铝板带生产上的应用[J].上海有色金属.2004,25(2)：77-82.
[109]马锡良著.铝带坯连续铸轧生产[M].长沙：中南工业大学出版社,1992.3,第1版
[110]彭大暑主编.金属塑性加工原理[M].长沙：中南大学出版社,2004.2,第1版
[111]V.Hansen, B.Andersson, J.E.Tibbalis, and J.Gjqnnes. Metallurgical reactions in two industrially strip-cast aluminum-manganese alloy[J]. Metallurgical and Materials Transactions B.1995, Vol.26A:839-849
[112]王希维.铸轧铝板的组织及其缺陷[J].轻合金加工技术,1994,22(2)：14-17,
[113]司开田.铸轧5052合金冷隔缺陷产生的机理研究[J].铝加工,2007,3：27-29
[114]黄昌华.铸轧5052合金气道产生机理及其控制方法[J].铝加工,2009,1：55-57
[115]张冠星,马全仓,关绍康等.、富铈混合稀土对5052铝合金流动性及净化效果的影响[J].材料热处理学报,2008,29(4)：83-85
[116]王祝堂,田荣章主编.铝合金及其加工手册[M].长沙：中南大学出版社,1989.6,第1版
[117]高淑明,苏学常.5052合金H32板材稳定化处理[J].轻合金加工技术,1995,23(4)：24-27)
[118]Hanlian Zhu, A.K.Ghosh, K.Maruyama. Effect of cold rolling on microstructure and material properties of 5052 alloy sheet produced by continuous casting[J]. Materials Science and Engineering A419 (2006) 115-121
[119]朱日彰.金属腐蚀学[M].北京：冶金工业出版社,1993
[120]孙雅茹.镁合金表面处理方法及耐蚀性能研究[D].沈阳：沈阳工业大学硕士论文,2003
[121]张志富.镁合金腐蚀与防护的研究[D].西安：西北工业大学硕士论文,2004.
[122]徐萍.Ce, Nd、Sr对AZ91镁合金显微组织和腐蚀性能的影响[D].武汉：武汉理工大学硕士论文,2005
[123]美国哈兹列特板带铸造公司,大卫·哈兹列特.采用哈兹列特工艺把电解铝液加工成铝板带—节能又环保
[124]彭云冬,蒋元龙,宋乃春.电解铝液直接进行铸轧的节能效果[J].资源再生,2008,4：50-51
[125]井满清.青海省电解铝液直接铸坯优势分析[J].有色金属加工,2007,(2)：34-35
[126]马道章.节能降耗—哈兹列特铝板带连铸连轧工艺的优势[J].上海有色金属,2006,(1)：18-21
[2]http://www.investgz.gov.cn/zsproject/Readproject.asp?ID=3022.10万吨／年高精度铝板带及铝合金复合材料工程项目建议书
[3]http://www.cnitdc.com/juke/juke_bjfx.htm.巨科铝业进军铝加工业的背景分析
[4]肖亚庆主编.铝加工技术实用手册[M].北京：冶金工业出版社,2005
[5]钱宝华.加工工艺对5052合金板材组织与性能的影响[D].重庆：重庆大学,2008
[6]王祝堂,任柏峰,周涛.中国铝板带箔加工设备现状及发展方向[J].上海有色金属,2004,25(3)：128-132
[7]程磊,谢水生,黄国杰.中国铝板带箔轧制工业的发展[J].轻合金加工技术,2007,35(11)：12-17
[8]傅振有.铝及铝合金连续铸轧工艺及铸轧机列的设备组成[J].轻合金加工技术,1985,4：1-4
[9]潘世民.世界铝连续铸轧技术综述[J].世界有色金属,2003,3：49-51
[10]王祝堂.迈向新世纪的世界铝带坯铸轧[J].轻合金加工技术,2001,29(4)：8-10
[11]王祝堂.铝带坯双辊式连续铸轧技术的现状与新进展[J].世界有色金属,1997,7：18-21
[12]Kaiser Aluminum&Chemical Corporation. A method for making beverage can sheet [P]. World Intellectual Property Organization:Wo97/11205,1997-03-27
[13]范靖亚.戈尔登铝公司开发的连续铸轧高质量铝薄板[J].轻合金加工技术,1997,25(4)：27-29
[14]马道章.哈兹列特工艺在铝板带连铸连轧应用中若干问题的探讨[J].铝加工,2005,162：18-24
[15]Peter Regan, Wojtek Szczypiorski. 哈兹列特工艺及其在中国的前景.2005
[16]刘小玲,马道章.浅谈哈兹列特连铸技术在我国铝板带生产上的应用[J].上海有色金属,2004,25(2)：77-82
[17]大卫.哈兹列特.采用哈兹列特工艺把电解铝液加工成铝板带.
[18]Hazelett Strip-casting Corporation. Non-rotating, levitating, cylindrical air-pillow apparatus and method for supporting and guiding an endless flexible casiting belt into the entrance of a continuous metal-casting machine [P]. World Intellectual Property Organization:Wo 01/08835A1,2001-08-02
[19]John M.A.Dompas. Belt back-up apparatus and coolant application means for twin-belt casting machines[P]. United States Patent:3937274,1976-2-10
[20]Hazelett Strip-casting Corpration. Magnetized finned backup rollers for guiding and stabilizing an endless casting belt[P]. Canadian Intellectual Property Office:CA 2259604,2005-06-07
[21]Alcan international limited. Surface texturing of casting belts of continuous casting machines[P]. World Intellectual Property Organization:WO2005/032743A1,2005-4-14
[22]Dr.Subodh, K.Das. Evaluation and characterization of in-line annealed continuous cast aluminum sheet. Final technical report, August2005
[23]James G.Morris, Chi-Sing Man, and Tongguang Zhai. prediction of texture and formability of continuous cast AA5000 and 2000 Series aluminum alloy sheets and their quality improvement.
[24]W.C.Liu, T.Zhai, J.G.Morris. Texture evolution of continuous cast and direct chill cast AA3003 aluminum alloys during cold rolling[J]. Scripta Materialia,2004,51:83-88
[25]W.C.Liu, Z.Li, C.S.Man. Effect of heating rate on the microstructure and tecture of continuous cast AA3105 aluminum alloy[J]. Materials Science and Engineering A,2008, 478:173-180
[26]W.C.Liu, J.G.Morris. Effect of hot and cold deformation on the P{011}<455> recrystallization tecture in a continuous cast Al-Mn-Mg aluminum alloy[J]. Scripta Materialia,2006,54:2095-2099
[27]Jiantao Liu, James G.Morris. Macro-, micro- and mesotecture evolutions of continuous cast and direct chill cast AA3105 aluminum alloy during cold rolling[J]. Materials and Engineering A,2003,357:277-296
[28]W.C.Liu, Z.Li, C.S.Man, D.Raabe, J.G.Morris. Effect of precipitation on rolling tecture evolution in continuous cast AA3105 aluminum alloy[J]. Materials Science and Engineering A,2006,434:105-113
[29]W.C.Liu, C.S.Man, D.Raabe, J.G.Morris. Effect of hot and cold deformation on the recrystallization tecture of continuous csat AA5052 aluminum alloy[J]. Scripta Materialia,2005,53:1273-1277
[30]Jiantao Liu, James G.Morris. Recrystallization microstructures and tectures in AA5052 continuous cast and direct chill cast aluminum alloy[J]. Materials Science and Engineering A,2004,385:342-351
[31]X.Y.Wen, Z.D.Long, W.M.Yin, T.Zhai, Z.Li, S.K.Das. Texture evolution in continuous casting aluminum alloy AA5052 hot band during biacial stretching[J]. Materials Science and Engineering A,2007,454-455:245-251
[32]Y.M.Zhao, W.Wen, J.G.Morris. The differences in particle structures and recrystallization behaviors beteeen DC and CC AA5052 aluminum alloys[J]. Materials Science and Engineering A,2004,373:167-174
[33]W.C.Liu, B.Radhakrishnan, Z.Li, J.G.Morris. Through-thickness tecture gradient in continuous cast AA5052 aluminum alloy sheet[J]. Materials Science and Engineering A, 2008,472:170-178
[34]W.C.Liu, J.G.Morris. Effect of hot and cold deformation on thepfiber rolling tecture in continuous cast AA5052 alumium alloy[J]. Scripta Materialia,2005,52:1317-1321
[35]X.F.Yu, Y.M.Zhao, X.Y.Wen, T.Zhai. A study of mechanical isotropy of continuous cast and direct chill cast AA5182 Al alloys[J]. Materials Science and Engineering A394(2005)376-384
[36]W.C.Liu, T.Zhai, J.G.Morris. Comparison of recrystallization and recrystallization tectures in cold rolled DC and CC AA5182 aluminum alloys[J]. Materials Science and Engineering A,2003,358:84-93
[37]W.C.Liu, J.G.Morris. Effect of initial tecture on the recrystallization tecture of cold rolled AA5182 aluminum alloy[J]. Materials Science and Engineering A,2005,402: 215-227
[38]W.C.Liu, J.G.Morris. Effect of pre-treantment on recrystallization and recry stallization tectures of cold rolled CC AA5182 aluminum alloy[J]. Materials Science and Engineering A,2003,363:253-262
[39]W.C.Liu, J.Li, H.Yuan and Q.X.Yang.Effect of recobery on the recrystallization tecture of an Al-Mg alloy[J]. Scripta Materialia,2007,57:833-836
[40]W.C.Liu, T.Zhai, C.S.Man, J.G.Morris. Quantification of recrystallization tecture evolution in cold rolled AA5182 aluminum alloy[J]. Scripta Materialia,2003,49: 539-545
[41]W.C.Liu, J.G.Morris. Comparison of the tecture evolution in cold rolled DC and SC AA5182 aluminum alloys [J]. Materials Science and Engineering A,2003,339:183-193
[42]J.Li, W.C.Liu, T.Zhai, E.A.Kenik. Comparison of recrystallization tecture in cold-rolled continuous cast AA5083 and 5182 aluminum alloys[J]. Scripta Materialia,2005,52: 163-168
[43]W.C.Liu, J.G.Morris. Kinetics of the formation of the β fiber folling tecture in continuous cast AA 5xxx series aluminum alloys[J].2002,47:743-748
[44]Xiang-Ming Cheng, James G.Morris. Tecture, microstructure and formability of SC and DC cast Al-Mg alloys[J]. Materials Science and Engineering A,2002,323:32-41
[45]马道章.生产蒙皮用铝合金板材的先进工艺[J].上海有色金属,2001,22(2)：80-82
[46]马道章.连铸连轧—降低汽车用铝材高成本的好工艺[J].轻合金加工技术,2006,34(6)：6-7
[47]关绍康.高性能铝合金车身板的产业化及发展趋势.河南省铝加工业发展研讨会专家报告篇.2004年9月
[48]Zhong Li, Steven Kirkland. Development of continuous cast 5754 alloy sheet for automotive application [J]. TMS,2005
[49]H.N.Azari, S.X.Girard, D.S.Wilkinson, and D.J.Lloyd. Effect of thermonechanical treatment on the evolution of rolling and recrystallization tectures in twin-belt cast AA5754 aluminum alloy[J]. Metallurgical and Materials Transactions A, Vol35A,2004: 1839-1851
[50]Alcan International Limited. Belt casting of non-ferrous and light metals and apparatus therefore [P]. World Intellectual Property Organization:Wo2005/032744,2005-04-14
[51]Nippon Light Metal Company, Ltd. Speed synchronization system of aluminum alloy slab continuous casting and rolling line and production facility and method of production of aluminum alloy contiuously cast and rolled slab using same[P]. World Intellectual Property Organization:Wo 2007/066448A1,2007-6-14
[52]Nippon Light Metal Co, Ltd. Aluminum alloy sheet method for manufacturing the same[P]. Word Intellectual Property Organization:Wo2006/011242,2006-2-2
[53]王祝堂.全球首条汽车铝板带连铸轧生产线投产[J].轻合金加工技术,2005,33(3)
[54]Nippon Light Metal Company Ltd. Method for producing Al-Mg-Si based aluminum alloy plate excellent in bake-hardenability[P]. European patent application: EP1715067A1,2006-10-25
[55]Nippon Light Metal Company Ltd. Method for producing Al-Mg-Si alloy excellent in bake-hardenability and hemmability[P]. European patent application:EP1702995A1, 2006-09-20
[56]王自涛.铝材应用发展机遇与挑战.第五届中国河南投资贸易洽谈会铝产业发展研讨会专业报告.2008年8月
[57]陈永禄,傅高升等.经高效熔体处理的易拉罐用铝带材的中间退火工艺探讨[J].有色金属加工,2003,32(1)：12-15
[58]彭开萍,陈文哲等.3004铝合金拉伸变形特征[J].机械工程材料,2005,29(12)：13-16
[59]彭开萍等.易拉罐用铝材锯齿屈服现象的研究[J].中国有色金属学报,2005,15(5)：694-699
[60]彭开萍等.3004铝合金动态应变时效的微观机理[J].材料热处理学报,2005,26(6)：57-61
[61]陈鸿铃等.高成形性罐用铝材热变形过程的微观组织观察[J].福建工程学院学报,2005,3(1)：61-65
[62]胡卓超张德芬黄涛等.3104铝合金的流变应力行为与动态再结晶[J].机械工程材料,2005,29(2)：6-9
[63]张德芬等.3104铝合金固溶及时效处理后的冷轧织构[J].材料热处理学报,2005,26(5)：88-91
[64]张德芬等.3104铝合金冷轧变形织构的分析.轻合金加工技术[J],2003,31(7)：22-25
[65]张德芬,黄涛等.3104铝合金再结晶织构的研究.材料工程[J],2004,11：28-31
[66]胡卓超等.电场退火对3104铝合金板显微组织与再结晶织构的影响[J].中国有色金属学报,2004,14(8)：1366-1371
[67]张德芬等.热轧3104铝合金的显微组织[J].有色金属,2004,56(4)：14-18
[68]张德芬,左良.预回复退火对3104铝合金再结晶织构和显微组织的影响[J].石油化工高等学校学报,2004,17(3)：62-65
[69]胡卓超,张德芬等.形变模式对3104铝合金板微取向流变行为的影响[J].材料科学与工艺,2005,13(1)：12-15
[70]黄光杰,汪凌云.3104铝合金板材织构和制耳行为研究[J].重庆大学学报,2000,23(3)：20-23
[71]黄光杰.3104铝合金高温塑性变形本构关系研究[J].材料导报,2006,20(7)：460-462
[72]黄光杰.3104铝合金流变应力行为[J].重庆大学学报.2007,30(1)：70-72
[73]沈健,张新明.3004铝合金的再结晶和织构[J].中南矿冶学院学报,1994,25(6)：
[74]沈健,张新明.中间退火对3004合金组织织构和各向异性的影响[J].1994,17(3)：44-47
[75]张明,温熙宇.3004铝合金铸轧板均匀化后冷轧的组织与织构[J].中国有色金属学报,1995,5(4)：151-153
[76]温熙宇,王玉林.3004铝合金铸轧板均匀化热处理的组织和织构[J].金属热处理学报,1994,15(3)：44-48
[77]温熙宇,王玉林等.罐材用3004铝合金铸轧板经中间退火和冷轧后所得冷轧板的ODF分析[J].轻金属,1994,3：43-45
[78]朱清洋.3104铝合金化学成分优化及织构研究[D].重庆：重庆大学,2006
[79]肖亚庆主编,铝加工技术实用手册[M].北京：冶金工业出版社,2005
[80]刘静安,盛春磊,朱英.铝材在包装、容器工业上的开发与应用[J].四川有色金属,2006.6第2期：1-8
[81]胡汉起编.金属凝固原理[M].北京：机械工业出版社,2000.11,第2版
[82]佟长清.3004合金铸锭锰偏析及均匀化处理[J].轻合金加工技术,1997,25(1)：31-36
[83]孙东立,姜东峰.均匀化处理对3004铝合金显微组织的影响[J].中国有色金属学报,1999,9(3)：556-558
[84]D.T.L. Alexander, A.L.Greer. Formation of eutectic intermetallic rosettes by entrapment of liquid droplets during cellular columnar growth[J]. Acta Materialia 52 (2004) 5853-5861
[85]Y.J.Li, L.Arnberg. Evolution of eutectic intermetallic particles in DC-cast AA3003 alloy during heating and homogenization[P]. Materials Science and Engineering A347 (2003) 130-135
[86]Novelis Inc. Method of and molten metal feeder for continuous casting[P]. World Intellectual Property Organization:Wo2006/089419A1,2006-8-31
[87]Hazelett Strip-Casting Corporation. Radial-flow distributor for wide uniform nonturbulent non-dribbline pouring of molten metal into a continuous metal-casting machine-methods and apparatus[P]. United States Patent:5804136,1998-9-8
[88]Peyman Ashtari, Kevin Gatenby. Reheating of solid shell during twin belt-casting of an Al-Fe-Si alloy[J]. Scripta Materialia 58 (2008) 150-153
[89]Peyman Ashtari and Kevin Gatenby. Formation of inverse segregation on the surface of belt-cast Al-Fe-Si and Al-Fe-Si-Mn alloys. Scripta Materialia 57 (2007) 627-630
[90]苏鸿英.用哈兹列特铸造工艺生产板材表面条纹的消除[J].有色金属加工,1995,6：20-24
[91]Wojtek Szczypiorki等.哈兹雷特连铸带材涂层的优越性[J].有色金属加工,1995第三期：30-35
[92]Pedro G.Q.NETTO, Roberto P.TAVARES, Mihaiela IS AC. A technique for the evaluation of instantaneous heat fluces for the horizontal strip casting of aluminum alloys[J]. ISIJ International, Vol.41 (2001), No.11:1340-1349
[93]B.Farouk, D.Apelian and Y.G.Kim. A numerical and experimental study of the solidification rate in a twin-belt caster[J]. Metallurgical Transactions B,1992, Volume 23B:477-492
[94]A.G.Gerber, A.C.M.Sousa. A parametric study of the Hazelett thin-slab casting process[J]. Journal of Materials Processing Technology 49 (1995) 41-56
[95]S.Bounds, G.Moran, K.Pericleous, M.Cross, and T.N.Croft. A computational model for defect prediction in shape castings based on the interaction of free surface flow, heat transter, and solidification phenomena[J]. Metallurgical and Materials Transactions B, Volume31B, june 2000:515-527
[96]M. Aghaie-khafri. The effect of homogentization on the recrystallization of an Al-Mn-Mg Alloy sheet[J]. Journal of Materials Science,2005,40:1135-1139
[97]S.Sarkar, M.A.Wells, W.J.Poole. Softening behaviour of cold rolled continuous cast and ingot cast aluminum alloy AA5754[J]. Materials Science and Engineering A 421 (2006) 276-285
[98]Jiantao Liu, Robert E.Dick, Joseph M.Fridy, Thomas N.Rouns. Crystallographic tecture evolution of continuous cast Al-Mn-Mg alloy sheet during cold rolling and annealing[P]. Materials Science and Engineering A458 (2007) 73-87
[99]王祝堂.铝及铝合金热轧时组织的变化[J].轻合金加工技术,2002,30(3)：8
[100]马道章.开辟易拉罐罐体材料生产的新途径[J].上海有色金属,2002,23(2)：70-73
[101]K.Marthinsen, O.Daaland, T.Turu, and E.Nes. The spatial distribution of nucleation sites and its effect on recrystallization kinetics in commercial aluminum alloys [J]. Metallurgical and Materials transactions A,2003, Vol.34:2705-2715
[102]张宝昌主编.有色金属及其热处理[M].西安：西北工业大学出版,1993.10,第1版
[103]J.M.Howe. Metallographi and differential scanning calorimetry analyses of precipitation and recrystallization in an Al-Mn alloy[J]. Metallurgical Transactions A, Vol.17A,1986: 593-605
[104]张忠玉主编.铝及铝合金工艺与设备[M].长沙：中南大学出版社,2006.11,第1版
[105]刘朝义,陈瑶贵.氟碳喷涂单层铝板的加工过程[J].中国建材科技,2003,12(4)：53-55
[106]赵志远.铝和铝合金牌号与金相图谱速用速查及金相检验技术创新应用指导手册[M].北京：中国知识出版社,2005：797-795
[107]荣宝星.HAZELETT双带连铸机和连轧设备[J].上海金属(有色分册),1987,8 (4)：48-55
[108]刘小玲,马道章.浅谈哈兹列特连铸技术在我国铝板带生产上的应用[J].上海有色金属.2004,25(2)：77-82.
[109]马锡良著.铝带坯连续铸轧生产[M].长沙：中南工业大学出版社,1992.3,第1版
[110]彭大暑主编.金属塑性加工原理[M].长沙：中南大学出版社,2004.2,第1版
[111]V.Hansen, B.Andersson, J.E.Tibbalis, and J.Gjqnnes. Metallurgical reactions in two industrially strip-cast aluminum-manganese alloy[J]. Metallurgical and Materials Transactions B.1995, Vol.26A:839-849
[112]王希维.铸轧铝板的组织及其缺陷[J].轻合金加工技术,1994,22(2)：14-17,
[113]司开田.铸轧5052合金冷隔缺陷产生的机理研究[J].铝加工,2007,3：27-29
[114]黄昌华.铸轧5052合金气道产生机理及其控制方法[J].铝加工,2009,1：55-57
[115]张冠星,马全仓,关绍康等.、富铈混合稀土对5052铝合金流动性及净化效果的影响[J].材料热处理学报,2008,29(4)：83-85
[116]王祝堂,田荣章主编.铝合金及其加工手册[M].长沙：中南大学出版社,1989.6,第1版
[117]高淑明,苏学常.5052合金H32板材稳定化处理[J].轻合金加工技术,1995,23(4)：24-27)
[118]Hanlian Zhu, A.K.Ghosh, K.Maruyama. Effect of cold rolling on microstructure and material properties of 5052 alloy sheet produced by continuous casting[J]. Materials Science and Engineering A419 (2006) 115-121
[119]朱日彰.金属腐蚀学[M].北京：冶金工业出版社,1993
[120]孙雅茹.镁合金表面处理方法及耐蚀性能研究[D].沈阳：沈阳工业大学硕士论文,2003
[121]张志富.镁合金腐蚀与防护的研究[D].西安：西北工业大学硕士论文,2004.
[122]徐萍.Ce, Nd、Sr对AZ91镁合金显微组织和腐蚀性能的影响[D].武汉：武汉理工大学硕士论文,2005
[123]美国哈兹列特板带铸造公司,大卫·哈兹列特.采用哈兹列特工艺把电解铝液加工成铝板带—节能又环保
[124]彭云冬,蒋元龙,宋乃春.电解铝液直接进行铸轧的节能效果[J].资源再生,2008,4：50-51
[125]井满清.青海省电解铝液直接铸坯优势分析[J].有色金属加工,2007,(2)：34-35
[126]马道章.节能降耗—哈兹列特铝板带连铸连轧工艺的优势[J].上海有色金属,2006,(1)：18-21