新型HID灯电子镇流器的研究
|
摘要
随着绿色照明计划在全球的推广,世界各国更加重视节能环保的照明器件的开发、研制和推广。由于气体放电灯具有发光效率高等优势,因而在照明领域得到了越来越广泛的应用,人们也把更多的目光投入到了电子镇流器等相关电路的研制中。
本文首先回顾了气体放电灯和电子镇流器的发展过程,分析了气体放电灯的发光原理和负阻特性。分析了在气体放电灯的建模、气体放电灯的声谐振、电子镇流器的控制方法、电子镇流器启动电路及电子镇流器的结构等方面的研究现状,分析比较了三种单级式电子镇流器的工作原理。
本文利用改进的Francis气体放电灯模型建立了高强度气体放电灯的数学模型,并用SIMULINK进行了仿真,观测该模型在50Hz和50KHz输入正弦信号作用下的电压、电流、电导等参数的变化情况。仿真结果表明该模型和实际的高强度气体放电灯(HID)特性比较一致。
鉴于斩控式交流调压电路在电路结构、功率因数等方面的优良性能,本文提出了一种新型的基于交流斩波电路的单级式电子镇流器方案,设计了单管反串联电子开关交流斩波电路,使用非互补控制方式对开关管进行控制,并用SIMULINK进行了仿真调试。通过调节交流斩波电路的电感、电容等参数,使电路工作在电流断续模式。同时将电子镇流器串接气体放电灯系统等效为一个受控电流源与气体放电灯串联的电路,用SIMULINK进行仿真,验证所设计的这种电子镇流器的可行性。
在理论分析和SIMULINK仿真的基础上,本文将设计的电子镇流器用硬件电路实现,搭建了样机,进行了实验。该样机设计了脉冲时序电路、电压电流检测电路等,采用恒流控制方式,选用了PIC16F877单片机完成系统控制。实验结果表明,该样机能实现调压调光功能,实现恒流控制,达到了设计目标。
As the plan of Green Illumination is promoted in the world, every country pays more attention to the development of lighting device characterized of energy saving and environmental protection. Compared to incandescent lamps, the gas discharge lamp of high luminous efficiency has been used in the field of lighting more and more widely.And a lot of time is spend on the design of electronic ballast.
In this paper, background knowledge on gas discharge lamp and electronic ballast is introduced firstly, and the light-emitting principle of the gas discharge lamp and characteristics of negative incremental impedance are analyzed. The modelling of gas discharge lamps, acoustic resonance of gas discharge lamp, control methods for electronic ballasts, igniter circuit of electronic ballasts and structures of electronic ballast are presented, and the working principle of three kinds of single-stage electronic ballasts is analyzed.
In this paper, a modified model of gas discharge lamp is used to establish a mathematical model of high-intensity gas discharge lamp, which is carried out with SIMULINK toolbox. With input signal of 50Hz and 50KHz sinusoidal, the current, conductivity and other changes in parameters of the model are observed.
Considering the excellent performance of AC chopper, a novel single stage electronic ballast based on AC chopper is proposed in this paper,and a single-tube electronic switch anti-Series AC chopper and non-complementary control of the switches are used. By simulating and debugging, the parameter of inductance and capacitance in chopper circuit in discontinuous current mode is regulated.On the basis of the analysis of the characteristics of the output signal in AC Chopper circuit, AC Chopper circuit in series with gas discharge lamp ballast is equivalent to a controlled current source in series with gas discharge lamp.
In the full theoretical analysis and simulation based on SIMULINK, prototype for the novel electronic ballast designed in this paper is generated, including pulse timing circuits, voltage/current detection circuits and so on. Many control functions is implemented by PIC16F877 MCU. Experimental results show that the prototype can achieve dimming regulator and constant-current control, and achieve the design goals.
本文首先回顾了气体放电灯和电子镇流器的发展过程,分析了气体放电灯的发光原理和负阻特性。分析了在气体放电灯的建模、气体放电灯的声谐振、电子镇流器的控制方法、电子镇流器启动电路及电子镇流器的结构等方面的研究现状,分析比较了三种单级式电子镇流器的工作原理。
本文利用改进的Francis气体放电灯模型建立了高强度气体放电灯的数学模型,并用SIMULINK进行了仿真,观测该模型在50Hz和50KHz输入正弦信号作用下的电压、电流、电导等参数的变化情况。仿真结果表明该模型和实际的高强度气体放电灯(HID)特性比较一致。
鉴于斩控式交流调压电路在电路结构、功率因数等方面的优良性能,本文提出了一种新型的基于交流斩波电路的单级式电子镇流器方案,设计了单管反串联电子开关交流斩波电路,使用非互补控制方式对开关管进行控制,并用SIMULINK进行了仿真调试。通过调节交流斩波电路的电感、电容等参数,使电路工作在电流断续模式。同时将电子镇流器串接气体放电灯系统等效为一个受控电流源与气体放电灯串联的电路,用SIMULINK进行仿真,验证所设计的这种电子镇流器的可行性。
在理论分析和SIMULINK仿真的基础上,本文将设计的电子镇流器用硬件电路实现,搭建了样机,进行了实验。该样机设计了脉冲时序电路、电压电流检测电路等,采用恒流控制方式,选用了PIC16F877单片机完成系统控制。实验结果表明,该样机能实现调压调光功能,实现恒流控制,达到了设计目标。
As the plan of Green Illumination is promoted in the world, every country pays more attention to the development of lighting device characterized of energy saving and environmental protection. Compared to incandescent lamps, the gas discharge lamp of high luminous efficiency has been used in the field of lighting more and more widely.And a lot of time is spend on the design of electronic ballast.
In this paper, background knowledge on gas discharge lamp and electronic ballast is introduced firstly, and the light-emitting principle of the gas discharge lamp and characteristics of negative incremental impedance are analyzed. The modelling of gas discharge lamps, acoustic resonance of gas discharge lamp, control methods for electronic ballasts, igniter circuit of electronic ballasts and structures of electronic ballast are presented, and the working principle of three kinds of single-stage electronic ballasts is analyzed.
In this paper, a modified model of gas discharge lamp is used to establish a mathematical model of high-intensity gas discharge lamp, which is carried out with SIMULINK toolbox. With input signal of 50Hz and 50KHz sinusoidal, the current, conductivity and other changes in parameters of the model are observed.
Considering the excellent performance of AC chopper, a novel single stage electronic ballast based on AC chopper is proposed in this paper,and a single-tube electronic switch anti-Series AC chopper and non-complementary control of the switches are used. By simulating and debugging, the parameter of inductance and capacitance in chopper circuit in discontinuous current mode is regulated.On the basis of the analysis of the characteristics of the output signal in AC Chopper circuit, AC Chopper circuit in series with gas discharge lamp ballast is equivalent to a controlled current source in series with gas discharge lamp.
In the full theoretical analysis and simulation based on SIMULINK, prototype for the novel electronic ballast designed in this paper is generated, including pulse timing circuits, voltage/current detection circuits and so on. Many control functions is implemented by PIC16F877 MCU. Experimental results show that the prototype can achieve dimming regulator and constant-current control, and achieve the design goals.
引文
[1]刘晨阳,气体放电灯电子镇流器关键技术的研究:[博士学位论文],浙江;浙江大学,2005
[2]吕晓东,集中式HID电子镇流器及其供电系统的研究:[博士学位论文],浙江;浙江大学,2005
[3]程为彬,高强度气体放电灯电子镇流技术研究:[博士学位论文],陕西;西安理工大学,2007
[4]霍菲阳,高压钠灯用大功率电子镇流器的研究:[硕士学位论文],黑龙江;哈尔滨理工大学,2008
[5]李冠忠,节能型数字镇流器研究:[硕士学位论文],山东;山东科技大学,2008
[6]张宏,紫外线消毒灯用可调光电子镇流器的研究:[硕士学位论文],辽宁;大连理工大学,2006
[7]赵军,380V/600W及新型两级低频方波HID灯电子镇流器的研究:[硕士学位论文] ,浙江;浙江大学,2004
[8]李桦,微机控制及新型两级HID灯电子镇流器的研究:[硕士学位论文],浙江;浙江大学,2005
[9]沈淼森,高强度气体放电灯电子镇流器关键技术研究:[硕士学位论文],浙江;浙江大学,2003
[10]车一曼,小功率高强度气体放电灯电子镇流器的研究:[硕士学位论文],天津;天津大学,2007
[11]杨永兵,70W金卤灯单级低频方波电子镇流器及其稳定性研究:[硕士学位论文] ,浙江;浙江大学,2005
[12]江兆根,电子镇流器控制方法仿真平台:[硕士学位论文],上海;同济大学,2008
[13]马志保,400W高压钠灯高频电子镇流器的研究:[硕士学位论文],安徽;合肥工业大学,2005
[14]朱国忠,高强度气体放电灯电子镇流器的研制:[硕士学位论文],浙江;浙江大学,2007
[15]陈铭,数字控制的金卤灯用电子镇流器:[硕士学位论文],浙江;浙江大学,2005
[16]杨国仁,HID电子镇流器及其Saber仿真:[硕士学位论文],浙江;浙江大学,2006
[17]许建炳,低频方波HID灯电子镇流器关键技术研究:[硕士学位论文],浙江;浙江大学,2006
[18]韩颖,多通信模式调光型HPS灯电子镇流器的研究:[硕士学位论文],黑龙江;哈尔滨工业大学,2007
[19]姚冬敏,智能数字化大功率金卤灯电子镇流器的研究与设计:[硕士学位论文],黑龙江;哈尔滨工业大学,2007
[20]潘耀章,高强度气体放电灯及其电子镇流器系统的建模与仿真:[硕士学位论文],黑龙江;哈尔滨工业大学,2007
[21]郝胜玉,可调光电子镇流器的设计研究:[硕士学位论文],山东;山东大学,2008
[22]黄秋凯,600W高压钠灯调光型电子镇流器研究:[硕士学位论文],浙江;浙江大学,2004
[23]郭蓉,小功率金卤灯启动问题研究及镇流器设计:[硕士学位论文],浙江;浙江大学,2006
[24]周成虎,单级有源功率因数校正电子镇流器触发电路研究:[硕士学位论文],河南,郑州大学,2007
[25]李桂臣,高功率因数高低压钠灯电子镇流器的研制:[硕士学位论文],安徽;合肥工业大学,2006
[26]吴岚龙,新型可调光荧光灯电子镇流器的设计:[硕士学位论文],江苏;南京理工大学,2007
[27]王雪飞,400W高压钠灯电子镇流器的研究:[硕士学位论文],安徽;合肥工业大学,2004
[28]唐宇,低压直流供电HID灯数字化电子镇流器研究:[硕士学位论文],黑龙江;哈尔滨工业大学,2008
[29]金亦青,数字控制金卤灯用电子镇流器研究:[硕士学位论文],浙江,浙江大学,2004
[30]阮景义,太阳能HID灯电子镇流器研究与设计:[硕士学位论文],安徽;合肥工业大学,2006
[31]俞安琪,赵文斌,蒋航,金属卤化物灯电感镇流器与电子镇流器的综合比较,中国照明电器,2007,01:20~25
[32]李相阳,徐殿国,张相军等,Buck功率因数校正电路在金卤灯镇流器中的应用,中国照明电器,2006,5:8~11
[33]杨华,徐殿国,李向阳,电子镇流器局部热点分析,佳木斯大学学报(自然科学版),2006,04:226~228
[34]杨卫,刘桂花,基于电荷泵功率因数校正技术的小功率高压钠灯用电子镇流器,绿色照明,2007,09:27~30
[35]杨华,徐殿国,郎永强,一种小功率低压钠灯数字电子镇流器的设计,电工技术学报,2007,08:80~83
[36]杨华,徐殿国,江檀,一种小功率电子镇流器起动电路研究,电气应用,2006,25(4),134~136
[37]于志,王卫,徐殿国,一种用于投影光源的高性能电子镇流器,电子器件,2007,30(1),100~104
[38]徐殿国,王茂均,针对高强度气体放电灯整流效应的保护方法研究,中国照明电器,2007,05:1~4
[39]刘汉奎,张相军,徐殿国,直流供电低压钠灯数字化电子镇流器设计,电力电子技术,2007,41(2):90~92
[40]徐殿国,张相军,莫桂林,汽车HID前大灯启动和过渡特性研究,中国照明电器,2005,9:6~11
[41]王建新,林国庆,一种电子镇流器控制方法的研究,电气应用,2008,27(5):83~86
[42]刘群,戴碧君,雷卫军,PWM整流器高功率因数的实现,通信电源技术,2003,2:20~22
[43]曾琪琳,黄耘,宋庭熙,单片机控制交流斩波调压装置,1997,16(2):44~47
[44]张庆范,王宁宁,单相GTO-PWM交流斩波器,1994,4:29~30
[45]李晓明,王长友,乔毅,基于DSP的大功率交流调压电源的设计,2008,11(5):6~9
[46]王勉华,交流斩波调压方式的探讨,煤矿自动化,1993,2:29~33
[47]余训玮,邹云屏,张杰,交流斩波调压技术在正弦波调光设备中的应用,通信电源技术,2007,24(2):43~48
[48]毛行奎,张文雄,交流斩波调压技术探讨,机床电器,2004,02:118~121
[49]俞红祥,纪延超,林敏,交流斩波器的新型谐波抑制脉宽调制技术,中国电机工程学报,2005,25(5):68~73
[50]车一曼,吴爱国,斩控式交流调压技术研究,机电设备,2006,6;19~22
[51]房绪鹏,斩控式交流调压器的几种新型拓扑,电力电子技术,2001,1:45~47
[52]洪峰,孙刚,蔡兆奇等,双Buck双向交流斩波器,2008,28(18):18~22
[53] Cecilio Blanco,Juan C.A Discharge Lamp Model Based on Lamp Dynamic Conductance. Power Electronics.2007,43:1191~1198
[54] Blanco, C., Anton, J.C., Robles, A..A Discharge Lamp Model Based on Lamp Dynamic Conductance. Power Electronics,2007,22(3):727~734
[55] Anton J.C., Blanco C., Ferrero, F..Simulation of the dynamic behaviour of HID lamps based on electrical conductance. Instrumentation and Measurement Technology Conference. 2003,2:1359~1363
[56] Anton J.C., Blanco C., Ferrero F.. An equivalent conductance model for high intensity discharge lamps. Industry Applications Conference, 2002. 37th IAS Annual Meeting.2002,2:1494~1498
[57] Chien-Ming Huang,Tsong-Juu Liang.A Novel Constant Power Control Circuit for HID Electronic Ballast. Power Electronics.2007,22:1573~1582
[58] Edward Deng,Slobodan Cuk.Negative Incremental Impedance and Stability of Fluorescent Lamp. Applied Power Electronics Conference and Exposition, 1997. 1997,2:1050~1056
[59] Co M.A.,Brumatti M.,Simonetti, D.S.L..Single Stage Electronic Ballast For HID Lamp. Industry Applications Conference, 2003. 38th IAS Annual Meeting. 2003,1:339~344
[60] Lam J., Jain P.K..A Low Cost Single-Stage Electronic Ballast with Unity Power Factor Using a Novel Single Switch Current Fed Resonant Inverter Topology. Power Electronics Specialists Conference, 2007. 2007:3106~3111
[61] Jang-Hyoun Youm,Hyun-Lark Do,Bong-Hwan Kwon.A Single-Stage Electronic Ballast with High Power Factor. Industrial Electronics.2000,47(3):716~718
[62] Chien-Ming Huang, Tsorng-Juu Liang,Lin, R.-L.,Jiann-Fuh Chen.A Novel Constant Power Control Circuit for HID Electronic Ballast. Power Electronics.2007,22(3):854~862
[63] V.J.Francis. Fundamentals of Discharge Tube Circuits. Methuen and Co.LTD, 1948:39~48
[64] Waymouth J F. Electric Discharge Lamp. The M.I.T press,1971.
[65] Peek S C, Domina Eberle Spencer. Performance of Electronic Ballast and Controls with 34-Watt F40 Fluorescent lamps. IEEE IA, 1989,25(6):1049~1059
[66] Yan Wei, Hui S Y R,Chung H.Nonlinear high-intensity discharge lamp model including a dynamic electrode voltage drop. Science,Measurement and Technology, 2003,150(4):161~167
[67] M. Shvartsas, S. Ben-Yaakov. A SPICE compatible model of high intensity discharge lamps. Power Electronics Specialists Conference, 1999, 2(2):1037~1042
[68] U. Mader, P. Horn. A dynamic model for the electrical characteristics of fluorescentlamps. Industry Applications Society Annual Meeting, 1992,2: 1928~1934
[69] Hiroshi Bo, Kazuyoshi Masumi.Model equation characteristics of high-frequency fluorescent lamps. Tola and Bo Lighting Research and Technology,1986, 18: 65-70
[70]张东辉,严萍,高迎慧, MH灯用单级逆变器的研究,电力电子技术,2006,05:93~94
[71]李学海,PIC单片机实用教程,北京:北京航空航天大学出版社,2007:2~48
[72]刘笃仁,PIC软硬件系统设计,北京:电子工业出版社,2005:1~153
[73]武峰,陈新建,盛春花,PIC系列单片机开发应用实战,北京:北京航空航天大学出版社,2003:1~152
[74] Microchip PIC系列单片机原理、应用与开发,北京:国防工业出版社,2004:21~191
[75]康华光,电力电子基础,北京:高等教育出版社,1998:155~426
[76]王兆安,黄俊,电力电子技术,北京:高等教育出版社,2005:43~178
[77]路秋生,电子镇流器的设计与调光控制,北京:科技出版社,2005.1~277
[78]路秋生,常用电子镇流器电路及应用,北京:人民邮电出版社,2006.1~275
[79]路秋生,高频交流电子镇流器技术与应用,北京:人民邮电出版社,2004.1~369
[80]陈传虞,电子节能灯语电子镇流器的原理与制造,北京:人民邮电出版社,2004.1~317
[2]吕晓东,集中式HID电子镇流器及其供电系统的研究:[博士学位论文],浙江;浙江大学,2005
[3]程为彬,高强度气体放电灯电子镇流技术研究:[博士学位论文],陕西;西安理工大学,2007
[4]霍菲阳,高压钠灯用大功率电子镇流器的研究:[硕士学位论文],黑龙江;哈尔滨理工大学,2008
[5]李冠忠,节能型数字镇流器研究:[硕士学位论文],山东;山东科技大学,2008
[6]张宏,紫外线消毒灯用可调光电子镇流器的研究:[硕士学位论文],辽宁;大连理工大学,2006
[7]赵军,380V/600W及新型两级低频方波HID灯电子镇流器的研究:[硕士学位论文] ,浙江;浙江大学,2004
[8]李桦,微机控制及新型两级HID灯电子镇流器的研究:[硕士学位论文],浙江;浙江大学,2005
[9]沈淼森,高强度气体放电灯电子镇流器关键技术研究:[硕士学位论文],浙江;浙江大学,2003
[10]车一曼,小功率高强度气体放电灯电子镇流器的研究:[硕士学位论文],天津;天津大学,2007
[11]杨永兵,70W金卤灯单级低频方波电子镇流器及其稳定性研究:[硕士学位论文] ,浙江;浙江大学,2005
[12]江兆根,电子镇流器控制方法仿真平台:[硕士学位论文],上海;同济大学,2008
[13]马志保,400W高压钠灯高频电子镇流器的研究:[硕士学位论文],安徽;合肥工业大学,2005
[14]朱国忠,高强度气体放电灯电子镇流器的研制:[硕士学位论文],浙江;浙江大学,2007
[15]陈铭,数字控制的金卤灯用电子镇流器:[硕士学位论文],浙江;浙江大学,2005
[16]杨国仁,HID电子镇流器及其Saber仿真:[硕士学位论文],浙江;浙江大学,2006
[17]许建炳,低频方波HID灯电子镇流器关键技术研究:[硕士学位论文],浙江;浙江大学,2006
[18]韩颖,多通信模式调光型HPS灯电子镇流器的研究:[硕士学位论文],黑龙江;哈尔滨工业大学,2007
[19]姚冬敏,智能数字化大功率金卤灯电子镇流器的研究与设计:[硕士学位论文],黑龙江;哈尔滨工业大学,2007
[20]潘耀章,高强度气体放电灯及其电子镇流器系统的建模与仿真:[硕士学位论文],黑龙江;哈尔滨工业大学,2007
[21]郝胜玉,可调光电子镇流器的设计研究:[硕士学位论文],山东;山东大学,2008
[22]黄秋凯,600W高压钠灯调光型电子镇流器研究:[硕士学位论文],浙江;浙江大学,2004
[23]郭蓉,小功率金卤灯启动问题研究及镇流器设计:[硕士学位论文],浙江;浙江大学,2006
[24]周成虎,单级有源功率因数校正电子镇流器触发电路研究:[硕士学位论文],河南,郑州大学,2007
[25]李桂臣,高功率因数高低压钠灯电子镇流器的研制:[硕士学位论文],安徽;合肥工业大学,2006
[26]吴岚龙,新型可调光荧光灯电子镇流器的设计:[硕士学位论文],江苏;南京理工大学,2007
[27]王雪飞,400W高压钠灯电子镇流器的研究:[硕士学位论文],安徽;合肥工业大学,2004
[28]唐宇,低压直流供电HID灯数字化电子镇流器研究:[硕士学位论文],黑龙江;哈尔滨工业大学,2008
[29]金亦青,数字控制金卤灯用电子镇流器研究:[硕士学位论文],浙江,浙江大学,2004
[30]阮景义,太阳能HID灯电子镇流器研究与设计:[硕士学位论文],安徽;合肥工业大学,2006
[31]俞安琪,赵文斌,蒋航,金属卤化物灯电感镇流器与电子镇流器的综合比较,中国照明电器,2007,01:20~25
[32]李相阳,徐殿国,张相军等,Buck功率因数校正电路在金卤灯镇流器中的应用,中国照明电器,2006,5:8~11
[33]杨华,徐殿国,李向阳,电子镇流器局部热点分析,佳木斯大学学报(自然科学版),2006,04:226~228
[34]杨卫,刘桂花,基于电荷泵功率因数校正技术的小功率高压钠灯用电子镇流器,绿色照明,2007,09:27~30
[35]杨华,徐殿国,郎永强,一种小功率低压钠灯数字电子镇流器的设计,电工技术学报,2007,08:80~83
[36]杨华,徐殿国,江檀,一种小功率电子镇流器起动电路研究,电气应用,2006,25(4),134~136
[37]于志,王卫,徐殿国,一种用于投影光源的高性能电子镇流器,电子器件,2007,30(1),100~104
[38]徐殿国,王茂均,针对高强度气体放电灯整流效应的保护方法研究,中国照明电器,2007,05:1~4
[39]刘汉奎,张相军,徐殿国,直流供电低压钠灯数字化电子镇流器设计,电力电子技术,2007,41(2):90~92
[40]徐殿国,张相军,莫桂林,汽车HID前大灯启动和过渡特性研究,中国照明电器,2005,9:6~11
[41]王建新,林国庆,一种电子镇流器控制方法的研究,电气应用,2008,27(5):83~86
[42]刘群,戴碧君,雷卫军,PWM整流器高功率因数的实现,通信电源技术,2003,2:20~22
[43]曾琪琳,黄耘,宋庭熙,单片机控制交流斩波调压装置,1997,16(2):44~47
[44]张庆范,王宁宁,单相GTO-PWM交流斩波器,1994,4:29~30
[45]李晓明,王长友,乔毅,基于DSP的大功率交流调压电源的设计,2008,11(5):6~9
[46]王勉华,交流斩波调压方式的探讨,煤矿自动化,1993,2:29~33
[47]余训玮,邹云屏,张杰,交流斩波调压技术在正弦波调光设备中的应用,通信电源技术,2007,24(2):43~48
[48]毛行奎,张文雄,交流斩波调压技术探讨,机床电器,2004,02:118~121
[49]俞红祥,纪延超,林敏,交流斩波器的新型谐波抑制脉宽调制技术,中国电机工程学报,2005,25(5):68~73
[50]车一曼,吴爱国,斩控式交流调压技术研究,机电设备,2006,6;19~22
[51]房绪鹏,斩控式交流调压器的几种新型拓扑,电力电子技术,2001,1:45~47
[52]洪峰,孙刚,蔡兆奇等,双Buck双向交流斩波器,2008,28(18):18~22
[53] Cecilio Blanco,Juan C.A Discharge Lamp Model Based on Lamp Dynamic Conductance. Power Electronics.2007,43:1191~1198
[54] Blanco, C., Anton, J.C., Robles, A..A Discharge Lamp Model Based on Lamp Dynamic Conductance. Power Electronics,2007,22(3):727~734
[55] Anton J.C., Blanco C., Ferrero, F..Simulation of the dynamic behaviour of HID lamps based on electrical conductance. Instrumentation and Measurement Technology Conference. 2003,2:1359~1363
[56] Anton J.C., Blanco C., Ferrero F.. An equivalent conductance model for high intensity discharge lamps. Industry Applications Conference, 2002. 37th IAS Annual Meeting.2002,2:1494~1498
[57] Chien-Ming Huang,Tsong-Juu Liang.A Novel Constant Power Control Circuit for HID Electronic Ballast. Power Electronics.2007,22:1573~1582
[58] Edward Deng,Slobodan Cuk.Negative Incremental Impedance and Stability of Fluorescent Lamp. Applied Power Electronics Conference and Exposition, 1997. 1997,2:1050~1056
[59] Co M.A.,Brumatti M.,Simonetti, D.S.L..Single Stage Electronic Ballast For HID Lamp. Industry Applications Conference, 2003. 38th IAS Annual Meeting. 2003,1:339~344
[60] Lam J., Jain P.K..A Low Cost Single-Stage Electronic Ballast with Unity Power Factor Using a Novel Single Switch Current Fed Resonant Inverter Topology. Power Electronics Specialists Conference, 2007. 2007:3106~3111
[61] Jang-Hyoun Youm,Hyun-Lark Do,Bong-Hwan Kwon.A Single-Stage Electronic Ballast with High Power Factor. Industrial Electronics.2000,47(3):716~718
[62] Chien-Ming Huang, Tsorng-Juu Liang,Lin, R.-L.,Jiann-Fuh Chen.A Novel Constant Power Control Circuit for HID Electronic Ballast. Power Electronics.2007,22(3):854~862
[63] V.J.Francis. Fundamentals of Discharge Tube Circuits. Methuen and Co.LTD, 1948:39~48
[64] Waymouth J F. Electric Discharge Lamp. The M.I.T press,1971.
[65] Peek S C, Domina Eberle Spencer. Performance of Electronic Ballast and Controls with 34-Watt F40 Fluorescent lamps. IEEE IA, 1989,25(6):1049~1059
[66] Yan Wei, Hui S Y R,Chung H.Nonlinear high-intensity discharge lamp model including a dynamic electrode voltage drop. Science,Measurement and Technology, 2003,150(4):161~167
[67] M. Shvartsas, S. Ben-Yaakov. A SPICE compatible model of high intensity discharge lamps. Power Electronics Specialists Conference, 1999, 2(2):1037~1042
[68] U. Mader, P. Horn. A dynamic model for the electrical characteristics of fluorescentlamps. Industry Applications Society Annual Meeting, 1992,2: 1928~1934
[69] Hiroshi Bo, Kazuyoshi Masumi.Model equation characteristics of high-frequency fluorescent lamps. Tola and Bo Lighting Research and Technology,1986, 18: 65-70
[70]张东辉,严萍,高迎慧, MH灯用单级逆变器的研究,电力电子技术,2006,05:93~94
[71]李学海,PIC单片机实用教程,北京:北京航空航天大学出版社,2007:2~48
[72]刘笃仁,PIC软硬件系统设计,北京:电子工业出版社,2005:1~153
[73]武峰,陈新建,盛春花,PIC系列单片机开发应用实战,北京:北京航空航天大学出版社,2003:1~152
[74] Microchip PIC系列单片机原理、应用与开发,北京:国防工业出版社,2004:21~191
[75]康华光,电力电子基础,北京:高等教育出版社,1998:155~426
[76]王兆安,黄俊,电力电子技术,北京:高等教育出版社,2005:43~178
[77]路秋生,电子镇流器的设计与调光控制,北京:科技出版社,2005.1~277
[78]路秋生,常用电子镇流器电路及应用,北京:人民邮电出版社,2006.1~275
[79]路秋生,高频交流电子镇流器技术与应用,北京:人民邮电出版社,2004.1~369
[80]陈传虞,电子节能灯语电子镇流器的原理与制造,北京:人民邮电出版社,2004.1~317