岩体节理多参数反演的反射波法研究
详细信息    本馆镜像全文|  推荐本文 |  |   获取CNKI官网全文
摘要
节理对岩体强度和稳定性有重要的影响,其影响程度直接与节理的几何参数和力学参数相关,包括节理的走向、倾角、位置、厚度、刚度、强度等。如何确定隐伏节理的特征参数,一直以来是岩体工程界关心和亟待解决的关键技术问题。目前岩体工程波动法测试中在对测试信号的解释和分析时往往只单一考虑波速、振幅衰减或频谱特点,使得节理波动探测成本高或是精度低,且获得的参数少。因此通过综合、深入分析节理反射信号,反演节理多个特征参数的研究无疑具有重要的理论意义和工程实用价值。
     垂直节理面入射应力波在节理内往返共线传播,向波源点发出多次回波,引起波源点的振动变化,根据正弦波形函数和Snell定律推导出各次回波的振幅与节理特征的关系式,据此建立节理多参数反演反射法理论模型。
     为接收到最理想的垂直节理面回波信号,需事先采用反射波反演出节理产状。从地表发出的应力波,经节理面反射后回到地表面,根据解析几何中点、线、面的关系,推导出节理面反射波走时,得出地表反射波等走时圆公式,从而建立起由测点反射波走时反演节理产状的理论模型。室内模型试验中,砂浆模拟岩石,湿砂层模拟节理,测试面(模型上表面)与节理面斜交,中心布置发射探头,接收探头四周布置,受面波、直达波干扰,无法直观判断出接收信号中反射波初至时刻,通过复信号分析可得到信号的瞬时信息,由瞬时频率能有效判断反射波初至时刻,得到五个测点处反射波走时。在MATLAB平台上编制程序,由测点走时搜寻出等走时圆圆心,进而得到节理面真倾向及倾角值,反演结果与模型设计值相差较小。
     另一个模型试验中测试面与节理面平行,采用垂直反射法测试(接、发探头并排微小间距摆置)。对测试信号作复信号分析,瞬时频率能清楚地显示出了各次回波的初至时刻;频谱分析表明测试信号中含有两个主频,分别对应发射探头的发射主频与测试面自振频率(采用ANSYS有限元程序作半空间体模态分析加以验证);采用Littlewood-Paley小波改造的带通滤波器分别滤出两个主频信号,滤出的信号均能反映出接收信号随各次回波的传至的变化规律。
     为从测试信号中提取出零次回波,采用Duhamel积分计算出探头发射信号激励下测试面的受迫振动,该受迫振动沿表面传播形成面波、直达波,借助于Laplace变换和Hankel变换可模拟出表面振动,受迫振动向下传播形成节理入射波,以该受迫振动的波形作为零次回波的波形,以测试信号消除零次回波后瞬时频率标准差最小作为评判标准,在MATLAB平台上编程搜寻出局部最小值,确定出零次回波的振幅值。
     提取零次回波的方法不适用于提取一次、二次回波,一方面是因为后至回波振幅减小,另一方面是因为应力波穿过节理层时衰减滤波,波形发生了变化。通过Hilbert变换可得到测试信号(一维)的平面迹线(二维),测试信号中只含有两个频率成分,视为双频信号,双频信号的平面迹线相当于两连杆绕平行轴转动时外杆杆端迹线,利用理论力学中运动合成和瞬心知识,推导出双频信号平面迹线步长平方满足余弦线性复合函数,而迹线转角可视为线性变化,据此可对回波到来之前的测试信号平面迹线作延长,得到一定长度的信号延展段,信号延展段与实测段作差可得到一次、二次回波的第一个波峰值。
     在得到各次回波第一个波峰值后,代入已建立的节理多参数反演理论模型,求出模型实验中节理的厚度、品质因子、波速等,较好地实现了多参数反演。
The joint has great effect on the strength and stability of rock mass, the effect degree directly relates to joint’s geometry and mechanics parameters, including the joint’s strike, dip angle, location, thickness, stiffness, strength et al. How to determine an underlying joint’s characteristic parameters has been a key technical subject which concerned by rock mass engineers. Present rock mass engineering wave testing always only consider wave velocity or amplitude attenuation or spectrum characteristics when the tested signal be complained and analyzed, as a result, the cost is high or precision is low when the technique be used to detect a joint, furthermore, only one or two parameters can be acquired. So a research on multi-parameter inversion for joint through comprehensive and further analysis of signal reflected by joint indubitably has important theoretic meaning and engineering practical value.
     Through the analysis of stress wave’s propagating process in the vertical direction at the joint, the expression of a series of echoes generated at the joint is achieved, then the combined vibration at the initial wave source is determined, finally a inverse model to detect the joint’s characters based on signal process of the vibration is given.
     Based on the analytic geometry theory, a formula to calculate the reflected wave’s traveling time can be deduced. The formula establishes a direct relationship between a joint’s real dip angle, real dip direction and the traveling time of testing spots. The reflected wave’s isotraveling time circle described by the formula has a clear conception and a definite meaning. Through complex signal analysis, a signal’s instantaneous amplitude, phase and frequency can be presented. A simulating jointed rock masses, mortar to simulate rock and wet soil layer to simulate joint, be made and the complex signal analysis be applied to analyze the vibration signal at the testing spots on the upper rock surface. Despite the Rayleigh wave’s serious interference, the initial arriving moment of the joint reflected wave can still be judged from instantaneous frequency efficiently. Using the complex signal analysis, the traveling time of several testing spots distributing around the source of vibration be get, a program based on MATLAB be written to search the center of the isotraveling time circle, then the joint’s attitude be inversed in the end.
     In the other simulating joint model the testing plane is parallel to the joint, the receiving probe be set close to the sending probe to receive the vertical reflected signal. Applying complex signal analysis to analyze the signal, the initial arriving moment of every echo be showed clearly by instantaneous frequency figure. The signal’s amplitude spectrum reveals that there are two main frequency, the higher is the probe signal’s dominant frequency and the lower is the testing plane’s free vibration frequency. The band-pass filter which be transformed from Littlewood-Paley wavelet can filter the two frequency signal separately, and the filtered signals display the change of the signal’s amplitude that corresponding with the each echo’s arrival.
     In order to separate initial echo from the tested signal, Duhamel integral be using to calculating the testing plane’s forced vibration motivated by the probe’s emitted signal. The forced vibration induces direct wave and Rayleigh wave which propagate along surface, with the help of LT and HT, the surface vibration be simulated. The forced vibration transmits downwards and induces incident wave for the joint, so the initial echo’s waveform is same as the forced vibration’s. A new signal can be get if initial echo be subtracted from the tested signal, set the new signal’s instantaneous frequency’s standard deviation as a assessment function, a program be designed on MATLAB to search the minimum, then the echo’s amplitude be obtained.
     Through Hilbert transform, a signal’s plane trace can be get. There are two frequencies in the tested signal, so the signal’s plane trace may be looked as the track of the out pole’s end when two poles rotate around parallel axles. Using the knowledge of motion synthesis in theory mechanics, a formula to describing the change of plane trace’s step length and angle for two-frequency be get. So we may prolongate the tested signal’s plane trace from the echo’s initial arriving moment, and get a certain length of the signal’s prolongation. If we subtract the prolongation from the real tested signal, the amplitude of 1st and 2nd echo be obtained.
     After the amplitude of every echo be obtained, we can use the inverse model to acquire the joint’s thickness, quality factor, P-wave velocity for the simulating model.
引文
[1] 王明洋,钱七虎. 爆炸应力波通过节理裂隙带的衰减规律[J]. 岩土工程学报. 1995,17(5):42~46.
    [2] Y.K. Wu. Propagation Characteristics of Blast-induced Shock Waves in Jointed Rock Mass[J]. Soil Dynamics and Earthquake Engineering, 17(1998): 407~412.
    [3] 王鲁明,赵坚,华安增等. 节理岩体中应力波传播规律研究的进展[J]. 岩土力学. 2003,24(Supp.): 602~610.
    [4] 鲁先元,高鹏飞,肖国强. 三峡坝基建基面岩体质量验收标准[J]. 岩石力学与工程学报. 1996.15(supp.): 599~604.
    [5] 肖志俊. 隧道围岩松弛范围的超声波测试分析[J]. 贵州教育学院学报. 2006.17(4):26~29.
    [6] 李 月,刘 立,梁 伟. 岩石松动层声波测试技术[J]. 西华大学学报. 2006.25(2):95~97.
    [7] 李雪峰,韩文峰,谌文武. 大柳树坝址松动岩体波速特征研究[J]. 岩石力学与工程学报. 2006.25(3): 596~600.
    [8] 樊启祥,史明勋. 混凝土无损检测技术在永久船闸中的应用[J]. 中国三峡建设. 2001.1:19~21.
    [9] 高靖国. 利用 MH—2 煤层厚度探测仪探顶煤厚度[J]. 山西煤炭. 1999.19(2):35~38.
    [10] 匡文龙,古德生,周科平等. GPR 在高速公路隧道掘进中掌子面前方岩体结构超前预报工作中的应用[J]. 公路交通科技. 2005.22(9):111~114.
    [11] 王正成,谭巨刚,孔祥春. 地质雷达在隧道超前预报中的应用[J]. 铁道建筑. 2005.2:9~11.
    [12] 吴俊,应松,李苍松. 路基挡墙背后回填质量声波检测新技术[J]. 路基工程. 2003(supp.): 29~31.
    [13] 李张明,练继建,戚蓝. 地震波动层析成像技术探测复杂岩体结构应用研究[J]. 岩石力学与工程学报. 2004.23(1):107~111.
    [14] 简文彬,吴振祥,邓鼎兴. 某地下工程围岩的声波频谱特性[J]. 岩土力学. 2003.24(supp.): 623~626.
    [15] 尹向宝. 超声波检测技术在岩体物性测试中的应用[J]. 煤炭技术. 2003.22(10): 89~90.
    [16] 卢文波. 应力波与可滑移岩石界面间的相互作用研究[J]. 岩土力学. 1996.17(3): 71-75.
    [17] 雷卫东,ASHRAFMH,滕军等. 二维波穿过单节理的透射率特性及其隐含意义[J]. 中国矿业大学学报. 2006.35(4):492~497.
    [18] M. S. King, Elastic wave propagation in and permeability for rocks with multiple parallel fractures[J]. International Journal of Rock Mechanics and Mining Sciences. 2002.39 (8):1033~1043.
    [19] 鞠杨,李业学,谢和平等. 节理岩石的应力波动与能量耗散[J]. 岩石力学与工程学报. 2006,25(2):2426-2434.
    [20] 崔新壮,陈士海,刘德成. 在裂隙岩体中传播的应力波的衰减机理[J]. 工程爆破. 1999,5(1): 18-21.
    [21] S. C. Fan, Y. Y. Jiao, J. Zhao. On modelling of incident boundary for wave propagation in jointed rock masses using discrete element method[J]. Computers and Geotechnics. 2004.31(1): 57~66.
    [22] J. Zhao, X.B. Zhao,J.G. Cai. A further study of P-wave attenuation across parallel fractures with linear deformational behaviour[J]. International Journal of Rock Mechanics and Mining Sciences. 2005.43(5)776~788.
    [23] 赵 坚, 陈寿根, 蔡军刚等. 用 UDEC 模拟爆炸波在节理岩体中的传播[J]. 中国矿业大学学报. 2002.31(2):111~115.
    [24] 李宁,韩烜,陈蕴生. 岩体节理刚度系数的现场声波测试[J]. 应用力学学报. 1998.15(3): 119~123.
    [25] 吴德伦,赵明阶. 岩石细观力学参数的反演研究[J]. 岩石力学与工程学报. 1996.15: 433~439.
    [26] 吴德伦, 黄质宏, 赵明阶. 岩石力学[M]. 重庆大学出版社. 2001.
    [27] 蔡美峰, 何满潮, 刘东燕. 岩石力学与工程[M]. 科学出版社. 2002.
    [28] 王靖涛. 桩基应力波检测理论及工程应用[M]. 地震出版社. 1999.
    [29] Rausche F., Goble G.G. Determination of pile damage by top measurements[J], Behavior of Deep Foundations, ASTM, STP670, Raymond Lundgren, Editor, ASTM, 1979, 500~506.
    [30] Rausche F. et al. Pile integrity testing and analysis. Proc. of the Fourth International Conference on the Application of Stress-Wave Theory to Piles, Rotterdam, the Netherlands, 1992.
    [31] 曹三华. 波反射法动测桩身完整性应注重的几个问题[J]. 矿业快报. 2002.393: 4~6.
    [32] 潘纪顺,梁慧云,姬计法等. 两种基桩无损检测方法的比较[J]. 地震研究. 2001.24(40): 370~374.
    [33] Palmer D. Refraction seismics(the lateral resolution of structure and seismic velocity)[M]. Yuan Ming-de, Wang Jian-mou translated. Beijing: Geological Publishing House: 14~89.
    [34] 谢明道. 垂直地震剖面法应用技术[M]. 石油工业出版社. 1991.
    [35] K. Vine, P. Cawley, A.J. Kinloch. Comparison of normal and oblique incidence ultrasonic measurements for the detection of environmental degradation of adhesive joints[J]. NDT & E International. 2002.35(4):241~253.
    [36] 廖全涛, 王建军. 浅层地震反射法在武汉长江隧道水上勘察中的应用[J]. 水文地质工程地质. 2006.3:124~127.
    [37] 黎霞. 浅层地震模型试验研究[J] 矿冶工程. 2006.16(2):14~19.
    [38] 何樵登. 地震勘探原理和方法[M]. 地质出版社. 1986.
    [39] 黄潮科 . 浅层反射地震勘探技术在珠江八大口门上的应用 [J]. 广东水利水电2002.(2)71~73.
    [40] 张广忠 , 刘貅生 . 浅层 地震技 术在隧道 勘察中的应 用 [J]. 煤田地质与 勘察 . 1998.26:49~54.
    [41] 陈成宗. 工程岩体声波探测技术[M]. 中国铁道出版社. 1990.
    [42] 吴德伦. 固体中的弹性波. 重庆大学出版社. 1993.
    [43] 刘 云 祯 . 瞬 态 面 波 法 的 数 据 采 集 处 理 系 统 及 其 应 用 实 例 [J]. 物 探 与 化 探 . 1996.20(1):28~31.
    [44] 赵明阶,黄卫东,韦刚. 公路土石混填路基压实度波动检测技术及应用[M]. 人民交通出版社. 2006.
    [45] 陈云敏 , 吴世明 . 成层 地基的 Reyleigh 波特征方程的解法 [J]. 浙江大学学 . 1991,25(1):40~52.
    [46] 夏唐代, 陈云敏. 匀质软夹层地基瑞利波弥散特性[J]. 振动工程学报. 1993,6(1):42~50.
    [47] 柴华友, 汪江波, 周一勤等. 瑞利波分析方法及应用进展[J]. 岩石力学与工程学报. 2002.21(1):119~124.
    [48] 中华人民共和国建设部. 多道瞬态面波勘察技术规程. JGT/T143-2004. 2004.
    [49] 冈田广,凌群. 一种新的地球物理勘探法—微动勘探法的原理和应用[A]. 见:全国地下目的物探测方法技术研讨会论文集[C]. 北京:中国纺织大学出版社,1996,70~76.
    [50] 汪东云. 工程地质与水文地质[M]. 重庆大学出版社. 1994.
    [51] 东南大学编著. 建筑结构抗震设计[M]. 中国建筑工业出版社. 1999
    [52] 中科院武汉岩土力学研究所智能仪器研究室. RSM—SY5 仪器操作说明. 2001.
    [53] 张英德, 刘江平, 刘良琼. Hilbert 变换在地质雷达数据处理中的应用[J]. 工程地球物理学报. 2004.1(4):54~57.
    [54] 余志雄,薛桂玉,周创兵. 复信号分析技术及其在地质雷达数字处理中的应用[J].岩石力学与工程学报. 2005.24(5):465~469.
    [55] 孙良环,李艳兰,熊晓燕. 希尔伯特变换原理在轴承故障诊断中的应用[J]. 机械管理开发. 2005,2:43~45.
    [56] 田涛,丁康. 希尔伯特变换及其在故障诊断中的应用[J]. 振动与冲击. 1996,15(2):24~27.
    [57] 李世雄. 小波变换及其应用[M]. 高等教育出版社. 1997.
    [58] 奥本海姆. 数字信号处理[M]. 北京:科学出版社.1982.
    [59] 黄长蓉. Hilbert 变换及其应用[J]. 成都气象学院学报. 1999.14(3):234~236.
    [60] 曹晖. 小波理论在结构抗震随机振动分析中的应用研究[D]. 重庆建筑大学博士学位论文. 1999.
    [61] 同济大学数学教研室. 高等数学. 高等教育出版社. 1992.
    [62] 谢明, 张晓飞, 丁康. 频谱分析中用于相位和频率校正的相位差校正法[J]. 振动工程学报. 1999.12(4): 454~459.
    [63] 丁康, 钟舜聪. 通用的离散频谱相位差校正方法[J]. 电子学报. 2003.31(1):142~145.
    [64] 张贤达. 非平稳信号分析与处理[M]. 国防工业出版社. 2001.
    [65] 胡昌华, 李国华, 刘涛等. 基于 MATLAB6.x 的系统分析与设计-小波分析[M]. 西安电子科技大学出版社. 2004.
    [66] 许年春. 库区移民新建区边坡土钉支护的合理设计与结构优化[D]. 重庆大学硕士学位论文. 2003.
    [67] 杨明. 加筋土挡墙的作用机理研究及其动力分析[D]. 重庆大学博士学位论文. 2001.
    [68] 美国 ANSYS 公司. ANSYS 动力分析指南. 2001.
    [69] 杨桂通, 弹塑性力学引论[M]. 清华大学出版社.2004.
    [70] 龙驭球. 结构力学[M]. 高等教育出版社. 2003.
    [71] R.克拉夫著. 王光远译. 结构动力学[M]. 高等教育出版社.1993.
    [72] 祁 皑, 范宏伟, 陈永祥. 简谐荷载作用下伴生自由振动的研究[J]. 地震工程与工程振动. 2002.22(6):156~161.
    [73] 徐龙军,谢礼立,郝 敏. 简谐波地震动反应谱研究[J]. 工程力学. 2005.22(5):7~13.
    [74] 贾启芬,刘习军. 理论力学[M]. 天津大学出版社.2003.
    [75] 张贵富. 瞬心及对瞬心的转动方程[J]. 金筑大学学报. 2000.4:107~109.
    [76] 王唐. 似是而非的定轴转动[J]. 晋中师专学报. 1997.1:37~39.
    [77] 高会生. Matlab 原理与工程应用[M]. 电子工业出版社.2006.
    [78] 李海波,蒋会军,赵 坚. 动荷载作用下岩体工程安全的几个问题[J]. 岩石力学与工程学报. 2003,22(11):1887~1891.
    [79] 李海波,冯海鹏,刘 博. 不同剪切速率下岩石节理的强度特性研究[J]. 岩石力学与工程学报. 2006,25(12):2635~2640.
    [80] 陈凡 , 王仁军 . 尺寸效应对基桩低应变完整性检测的影响 [J]. 岩土工程学报 . 1998.20(5):92~96.
    [81] 韩晓林,彭岳星,唐新鸣. 基桩检测反射波的非线性小波降噪重建方法[J]. 土木工程学报. 2004.34(6): 105~109.
    [82] 张良均,王靖涛,李国成. 小波变换在桩基完整性检测中的应用[J]. 岩石力学与工程学报. 2002.21(11):1735~1738.
    [83] Peter Huggenberger, Knoll M D, Knight Rosemary, et al. Ground probing radar as tool forheterogeneity estimation in gravel deposits[J]. Journal of Applied Geophysics, 1994, 31:171~184.
    [84] Scullion T., Saqrenketo T., Ground penetrating radar technique in monitoring defects in roads and highways[J]. Environmental and engineering geophysical society, ed, proceedings of the symposium on the application of geophysics to engineering and environmental problems, Orlando, Florida, 1995.63~72.
    [85] 谢明, 丁康. 频谱分析的校正方法[J]. 振动工程学报. 1994.7(2):172~178.
    [86] Barry H.,G.Brady, Dynamic Behavior of Rock[J], Dynamics/Rock Excavation, 1995: 611~624.
    [87] 赵明阶,徐蓉. 用弹性波速计算正交各向异性岩体的裂隙张量[J]. 重庆建筑大学学报. 1999.21(2): 42~48.
    [88] C. C. Xia, Z. Q. Yue, L. G. Tham et al. Quantifying topography and closure deformation of rock joints[J]. International Journal of Rock Mechanics and Mining Sciences. 2003.40(2):197~220.
    [89] R. D. Adams, B. W. Drinkwater. Nondestructive testing of adhesively-bonded joints[J]. NDT & E International. 1997.30(2):93~98.
    [90] M. D. Beard, M.J.S. Lowe. Non-destructive testing of rock bolts using guided ultrasonic waves[J]. International Journal of Rock Mechanics and Mining Sciences. 2003.40(4): 527~536.
    [91] J. G. Cai, J. Zhao. Effects of multiple parallel fractures on apparent attenuation of stress waves in rock masses[J]. International Journal of Rock Mechanics and Mining Sciences. 2000.37(4):661~682.
    [92] Wang Zhen-dong. Applied technique of shallow seis-mic exploration[M]. Beijing: Geological Publishing House,1988.
    [93] Sherifre,Geldart L P. Exploration seismology (Version-2)[M].Chu Ying,Li Cheng-chu,Wang Hong-wei, et.al translated. Beijing:Petroleum Industry Press:523~556.
    [94] C.S. Zhang, D.H. Zou, V. Madenga. Numerical simulation of wave propagation in grouted rock bolts and the effects of mesh density and wave frequency[J]. International Journal of Rock Mechanics and Mining Sciences. 2006.43(4):634~639.
    [95] P. DINEVA, D. GROSS, T. RANGELOV. Dynamic behavior of a cracked soldered joint[J]. Journal of Sound and Vibration. 2002.256(1): 81~102.
    [96] Hong Hao, Yaokun Wu, Guowei Ma et al. Characteristics of surface ground motions induced by blasts in jointed rock mass[J]. Soil Dynamics and Earthquake Engineering. 2001.21(2): 85~98.
    [97] 朱光明. 垂直地震剖面方法[M]. 石油工业出版社. 1988.
    [98] 冯 莉, 王 勤, 邓达康. 浅层地震记录中多次反射折射波的识别和消除[J]. 物探与化探.1998.22(4):324~328.
    [99] 赵 伟, 张青山, 杨 锋. 浅层地震与静力触探方法在黄土洞穴探测中的综合应用. 河南交通科技. 2000.20(4):56~59.
    [100] 吴有亮, 雷 宛, 李金玺. 溶洞的浅层地震反射特征及工程应用[J]. 工程勘察. 2006.(4):73~78.
    [101] Sjogen B. A brife study of application of the generalized reciprocal method[J]. Geoph Prosp,2000,48:815~834.
    [102] Tak M L. Controls of travel time date and problems of the generalized reciprocal method[J]. Geophysics, 2003,68:1626~1632.
    [103] Nazarian S.In-situ determination of elastic moduli of soil deposits and pavement systems by spectral-analysis-of-surface waves method[D]. Texas:Un Of Texas at Austin,1984.
    [104] Nazarian S,Desai M R. Automated surface wave method:field testing[J]. J. Geotech.Engrg. ASCE, 1993,119(7):1094~1111.
    [105] 任 青 文 . Rayleigh 表 面 波 理 论 频 散 曲 线 的 特 征 方 程 解 法 [J]. 河 海 大 学 学 报 . 1995,23(5):32~38.
    [106] 林维正, 苏勇. Rayleigh 表面波频散曲线的特征方程的计算方法[J]. 同济大学学报. 1997, 25(5):570~574.
    [107] 凡友华, 肖柏勋. 计算瑞利波频散曲线的快速矢量传递算法[J]. 湖南大学学报. 2002,29(5):25~30.
    [108] 夏唐代. 胡永生. 道路结构瑞利波特性及动力响应分析[J]. 郑州工业大学学报. 2000,21(1):19~22.
    [109] Addo K O, Robertson P K. Shear-wave velocity measurement of soils using Rayleigh waves[J]. Canadian Geotech Jr. 1992,29(3):558~568.
    [110] Malagnini L, Herrmann R B, Biella G, et al. Rayleigh wave in quarthary alluvium from explosive sources:determination of shear-wave velocity and Q structure. Bull. Seism. Soc. Am. 1995,85(3):900~922.
    [111] 韩嵩, 蔡美峰. 节理岩体物理模拟与超声波试验研究[J]. 岩石力学与工程学报. 2007,26(5):1026~103.
    [112] 赵明阶. 二维应力场作用下岩体弹性波速与衰减特性研究[J]. 岩石力学与工程学. 2007,26(1):123~130.
    [113] 范留明,闫娜,李宁. 薄弹性软弱夹层的动力响应模型[J]. 岩石力学与工程学. 2006,25(1):88~92.
    [114] 赵明阶. 裂隙岩体在受荷条件下的声学特性研究[D]. 重庆建筑大学博士学位论文. 1998.
    [115] 郭文章,等:节理岩体爆破研究进展,工程爆破,1999,Vol.5 No.4.
    [116] 高金石,张奇. 爆破理论与爆破优化[M],西安地图出版社,1993.
    [117] 许 明 , 张 永 兴 . 某 隧 道 锚 杆 完 整 性 的 无 损 检 测 方 法 [J]. 土 木 工 程 学 报 . 2004.37(5):437~440.
    [118] 许明, 张永兴. 锚杆动测问题的解析解[J]. 重庆建筑大学学报. 2003.25(3):215~217.
    [119] 施建新. 岩体灌浆检测方法及其适用性评价[J]. 水文地质工程地质. 2002. 4: 70~73.
    [120] 邱海涛,赵永贵,谭卓英等. 声波无损检测技术在南昆铁路隧道检测中的应用[J]. 广西地质. 2002.15(3): 75~78.
    [121] 李大心. 探地雷达方法及应用[M]. 北京:地质出版社,1994.
    [122] 邓昌宁,刘洋. 探地雷达在公路无损检测中的典型应用[J]. 东北公路. 2002,25(4):51~53.
    [123] 张玉海. 探地雷达在工程检测中的应用[J]. 混凝土. 2003.1:31~32.
    [124] 叶健, 陈松. 雷达法检测技术. 混凝土无损检测技术手册. 2003,280~311.
    [125] 朱国维,彭苏萍,王怀秀. 高频应力波检测锚固密实状况的试验研究[J]. 岩土力学. 2002.23(6): 787~791.
    [126] 陈达力. 岩石超声谱测试技术[J]. 岩石力学与工程学报. 1994. 13(1):59~68.

© 2004-2018 中国地质图书馆版权所有 京ICP备05064691号 京公网安备11010802017129号

地址:北京市海淀区学院路29号 邮编:100083

电话:办公室:(+86 10)66554848;文献借阅、咨询服务、科技查新:66554700