摘要
提出一种采用双铜-金刚石的"三明治"封装结构,利用有限元分析方法研究了其与传统的Cu+Cu W硬焊料封装结构激光器的热应力与Smile.对比模拟结果发现新封装结构热应力降低43.8%,Smile值增加95%.在次热沉热膨胀系数与芯片材料匹配的情况下,使用弹性模量更大的次热沉材料,可对芯片层热应力起到更好的缓冲作用.以硬焊料封装结构为例,分析了负极和次热沉厚度对器件Smile的影响.结果表明负极片厚度从50μm增加到300μm,器件工作结温降低2.26℃,Smile减小0.027μm,芯片的热应力增加22.95 MPa.当次热沉与热沉的厚度比小于29%时,Smile随次热沉厚度增加而增加;而当次热沉厚度超过临界点后,Smile随次热沉厚度增加而减小.当次热沉厚度达到临界点(2300μm)时,硬焊料封装的半导体激光器具有最大的Smile值3.876μm.制备了Cu W厚度分别为300μm和400μm的硬焊料封装976 nm激光器,并测量了其发光光谱.通过对比峰值波长漂移量,发现Cu W厚度增加了100μm,波长红移增加了1.25 nm,根据温度和应力对波长的影响率可知应力减小了18.05 MPa.测得两组器件的平均Smile值分别为0.904μm和1.292μm.实验证明增加Cu W厚度可减小芯片所受应力,增大Smile值.
A ″sandwich″ structure based on copper-diamond is proposed,the thermal stress and Smile of the proposed structure and traditional Cu + Cu W hard-solder packaged laser are studied by finite element analysis.Comparison of simulation results shows that the thermal stress of the new package structure is reduced by 43.8% and the Smile value is increased by 95%. When the coefficients of thermal expansion of laser chip and submount are matched,the submount materials with larger elastic modulus can better buffer the thermal stress of the chip. Taking the widely used Cu + Cu W hard-solder package structure as an example,the influence of negative electrode and substrate thickness on the Smile of diode laser chip is studied. It shows that when the thickness of the negative electrode increases from 50 μm to 300 μm,the junction temperature of the chip decreases by 2. 26 ℃,the Smile value decreases by 0. 027 μm,and the thermal stress increases by 22. 95MPa. When the thickness ratio of the substrate to the heat sink is less than 29%,the Smile value increases with the increase of the thickness of the heat sink,and when the ratio exceeds the critical point,the Smile value start to decrease. Hard-solder packaged semiconductor lasers have a maximum Smile value of 3. 876μm at a critical thickness of 2300 μm. Hard-solder packaged 976 nm lasers with Cu W thicknesses of 300 μm and 400μm are fabricated. The luminescence spectra are measured. By comparing the peak wavelength shifts,it is found that when the Cu W thickness increased by 100 μm,the red shift of wavelength increased by 1. 25 nm.According to the effect of temperature and stress on the wavelength,the stress is reduced by 18. 05 MPa; the average Smile values of the devices are also measured,which are 0. 904 μm and 1. 292 μm respectively.Experiments show that the increase in Cu W thickness can reduce the stress in the chip,but increase the Smile value.
引文
[1]LIU X S,DAVIS R W,HUGHES L C,et al.A study on the reliability of indium solder die bonding of high power semiconductor lasers[J].Journal of Applied Physics,2006,100(1):013104.
[2]SONG Yan-rong,HU Jiang-hai,ZHOU Jing-feng,et al.Laser diode-pumped Q-Switched Yb:LSO laser with a semiconductor saturable absorber mirror[J].Chinese Journal of Lasers,2006,33(10):1297-1300.宋晏蓉,胡江海,周劲峰,等.半导体可饱和吸收镜调Q的Yb∶LSO激光器[J].中国激光,2006,33(10):1297-1300.
[3]GAO Song-xin,WU De-yong,WANG Jun,et al.Multiplayer bonding technique for high power diode laser package[J].High Power Laser and Particle Beams,2003,15(5):447-449.高松信,武德勇,王骏,等.高功率二极管激光器封装的多层焊接技术[J].强激光与粒子束,2003,15(5):447-449.
[4]CAO Yin-hua,LIU You-qiang,QIN Wen-bin,et al.Kilowatt diode laser with beam quality better than All-Solid-State laser[J].Chinese Journal of Lasers,2009,36(9):2282-2285.曹银花,刘友强,秦文斌,等.光束质量超过全固态激光器的千瓦直接半导体激光器[J].中国激光,2009,36(9):2282-2285.
[5]LI Jing,CAO Yin-hua,LIU You-qiang,et al.Smile effect measurement of laser diode line arrays based on external cavity[J].Chinese Journal of Luminescence,2017,38(10):1302-1306李景,曹银花,刘友强,等.基于外腔反馈二极管线阵列的smile效应测量方法[J].发光学报,2017,38(10):1302-1306.
[6]CHEN Hua,LI Jing,ZHOU Xing-lin,et al.Measures to reduce Smile effect of semiconductor laser diode arrays caused by packaging thermal stress[J].Chinese Journal of Luminescence,2017,38(5):656-662陈华,李静,周兴林,等.封装热应力致半导体激光器“Smile”效应的抑制方法[J].发光学报,2017,38(5):656-662.
[7]SCHLEUNING D,GRIFFIN M,JAMES P,et al.Robust hard-solder packaging of conduction cooled laser diode bars[C].SPIE,2007,6456:645604.
[8]YUAN Zhen-bang,WANG Jing-wei,WU Di.Static and transient thermal behavior of high power semiconductor lasers[J].Chinese Journal of Lasers,2009,36(8):1957-1962.袁振邦,王警卫,吴迪,等.大功率半导体激光器阵列的稳态和瞬态热行为[J].中国激光,2009,36(8):1957-1962.
[9]LANG Chao,YAO Shun,CHEN Bing-zhen,et al.″Smile″effect on the beam quality for diode laser arrays[J].Chinese Journal of Lasers,2012,39(5):502006.郎超,尧舜,陈丙振,等.半导体激光器阵列的“Smile”效应对光束质量的影响[J].中国激光,2012,39(5):502006.
[10]TOMM J W,GERHARDT A,ELSAESSER T,et al.Simultaneous quantification of strain and defects in high-power diode laser devices[J].Applied Physics Letters,2002,81(17):3269-3271.
[11]FREVERT C,BUGGE F,KNIGGE S,et al.940 nm QCW diode laser bars with 70%efficiency at 1 k W output power at 203K:analysis of remaining limits and path to higher efficiency and power at 200K and 300K[C].SPIE,2016,9733:97330L.
[12]WANG Shu-na,ZHANG Pu,XIONG Ling-ling,et al.Influence of temperature on″Smile″in high power diode laser bars[J].Acta Photonica Sinica,2016,45(5):0514001王淑娜,张普,熊玲玲,等.温度对高功率半导体激光器阵列“Smile”的影响[J].光子学报,2016,45(5):0514001.
[13]LU Yao,NIE Zhi-qiang,CHEN Tian-qi,et al.Thermo-mechanical behavior of conduction-cooled high power diode laser arrays[J].Acta Photonica Sinica,2017,46(9):0914001.鲁瑶,聂志强,陈天奇,等.传导冷却单巴高功率半导体激光器热应力和Smile研究[J].光子学报,2017,46(9):0914001.
[14]WEIS,KAULFERSCH E,TOPFER M,et al.Design,simulation and technological realization of a reliable packaging concept for high power laser bars:proceedings of the Electronic Components&Technology Conference[C].IEEE,1998:0569-5503.
[15]SCHLEUNING D,SCHOLZ K,GRIFFIN M,et al.Material survey for packaging semiconductor diode lasers[C].SPIE,2009,7198:71981K.
[16]DU J,ZHOU H,SCHLEUNING D,et al.8xx nm k W conduction cooled QCW diode arrays with both electrically conductive and insulating submounts[C].SPIE,2008,6876:687605.
[17]TAN Yao-lin.Electroconductive diamond and its applications[J].Superhard Material Engineering,2007,19(3):32-34.谈耀麟.导电金刚石及其应用[J].超硬材料工程,2007,19(3):32-34.
[18]DU Yong-guo,ZHANG Wei-jun.The phystcal properties of the commonly-used electrical contact materials[J].Electrical Engineering Materials,2002,1(1):35-39.堵永国,张为军.常用触点材料的物理性能[J].电工材料,2002,1(1):35-39.
[19]ZHANG Xiu-rui,LI Huai-xue,HUANG Rui.Numerical simulation of thermal stress in hole-wall fabricated by nano-pulse laser drilling[J].Aeronautical Manufacturing Technology,2016,504(9):74-78.张修瑞,李怀学,黄锐.纳秒脉冲激光制孔孔壁热应力数值模拟研究[J].航空制造技术,2016,504(9):74-78.
[20]ZHANG Y,ZHAO Y P.Applicability range of Stoney's formula and modified formulas for a film/substrate bilayer[J].Journal of Applied Physics,2006,99(5):053513.
[21]STASKE R,SEBASTIAN J,WENZEL H,et al.Influence of mounting stress on polarisation degree of electroluminescence of laser diode bar[C].IEEE,2000:CWF99.
[22]WEN Y,BASARAN C.An analytical model for thermal stress analysis of multi-layered microelectronic packaging[J].Mechanics of Materials,2004,36(4):369-385.
